The steel used for the step shaft has an allowable shear stress of Tallow radius at the transition between the cross sections is r = 2.25 mm, determine the maximum torque T that can be applied. = 8 MPa. If the T 2 15 mm T 2

The steel used for the step shaft has an allowable shear stress of Tallow radius at the transition between the cross sections is r = 2.25 mm, determine the maximum torque T that can be applied. = 8 MPa. If the T 2 15 mm T 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
An extruded aluminum beam has the cross section shown. The vertical shear in the beam is 145 kN. Assuming a=85 mm, b-87 mm, c=7 mm and d=15 mm, determine the shear stress at (a) a and at (b) b a a/2 -b- The centroidal moment of inertia is given as ]x10-6 (m4)
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.80 in., a length of L1 = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.3 ksi. Brass segment (2) has an outside diameter of 0.60 in., a wall thickness of 0.05 in., a length of L2 = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.0 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.13 in., a length of L₂ = 28 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. y L₁ L2 TB. X (1) (2) N Answer: (a) TB = (b) T₁ = T₂= (c) DB = lb-ft lb-ft lb-ft rad B C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 45 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.6 ksi. Brass segment (2) has an outside diameter of 0.80 in., a wall thickness of 0.14 in., a length of L2 = 32 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.2 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.06 in., a length of L₂ = 24 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ (1) TB B L2 (2)
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring F and the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² E 6 ft -1 ft2 ft- AEF 2a in² 2 ft FO 60 kip D ACD= 1.5a in² C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.90 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.6 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.06 in., a length of L2 = 20 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.4 ksi. Determine: (a) the allowable torque Tg that can be applied to the compound shaft at flange B (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque T.
Q1/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple forces F causes the ends of the wrench to be displaced 3 mm, determine the maximum shear stress in the bolt. Assume that the wrench is rigid and modulus of rigidity of steel is 75 GPa. 150 mm i50 mm mni
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F