The strain components, ex= 940 micro strain, ey= -360 micro strain and yxy=830micro strain are given for a point in body subjected to plane strain. Determine; a. Magnitude of the principal strains b. The direction of the principal strain axes c. The maximum in-plane shear strain. Confirm your answer by means of Mohr's circle of strain and determine the linear strain on an axis inclined at 20 degrees clockwise to the direction of ey

The strain components, ex= 940 micro strain, ey= -360 micro strain and yxy=830micro strain are given for a point in body subjected to plane strain. Determine; a. Magnitude of the principal strains b. The direction of the principal strain axes c. The maximum in-plane shear strain. Confirm your answer by means of Mohr's circle of strain and determine the linear strain on an axis inclined at 20 degrees clockwise to the direction of ey

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.3P: An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the...

See similar textbooks

Similar questions

During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.
A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
Q4 A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Eb = 60 µ and Ec = 20 u . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction -30° (clockwise) with the x axis. 45 Pump
Q4 A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as ɛa = 80 µ , Ep = 60 µ and Ec = 20 µ . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction -30° (clockwise) with the x axis. a,x A c.y Pump
A uniaxial force was applied on the shown coupon during an experiment. The thickness, width and length of the coupon are 1mm, 20mm and 100 mm, respectively. the force applied had a magnitude of 1000N. A strain rosette was applied to the sample as shown. Strain gages a and c are perpendicular to each other. On the other hand, the angle between strain gages b and a is 30°. The strain gages reported the following strains Ea = -0.2x10-3 Ep = 0.667x10-3 Determine the elastic properties of the isotropic coupon. 30 a
QB3 TWO DIMENTIONAL STRAIN Three strain gauges were arranged in the form of a rectangular rosette and positioned on a test surface. The measured strains were as follows: E1 = 200x 106 E2 = 100 x 10-6 E3 = 50 x 10-6 Determine a) the principal strains and the principle stresses b) the direction of the greater principal strain relative to gauge 1 and sketch the Mohr strain circle. Take the Young Modulus of Elasticity value to be E = 200 GN/m² and Poisson's ratio u = 0.28.
Three readings are obtained from an equiangular strain gage rosette mounted on a free and unloaded surface of a part. Determine the magnitude of the principal strains and their orientation with respect to the 0° gage. Check the results with a Mohr circle.Assume The three known strains are all linear strains
The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.
1. Find the relationships between strain components in the polar coordinate and strain components in the rectangular coordinate.
The state of plane strain on an element is represented by the following components: Ex =D340 x 10-6, ɛ, = , yxy Ey =D110 x 10-6, 3D180 x10-6 ху Draw Mohr's circle to represent this state of strain. Use Mohrs circle to obtain the principal strains and principal plane.
Your answer is partially correct. The strain components for a point in a body subjected to plane strain are ɛ, = -890 µɛ, ɛ, = -690µɛ and yy = -682 prad. Using Mohr's circle, determine the principal strains (ɛp1 > Ep2), the maximum inplane shear strain yip, and the absolute maximum shear strain ymax at the point. Show the angle 0, (counterclockwise is positive, clockwise is negative), the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Answers: Ep1 = 927.99 με. Ep2 = 1116.0 PE. Vip = 188.01 prad. Ymax = -188.01 prad. Op = 36.82