The strut is supported by a pin at C and a steel guy wire AB. The wire AB has a diameter of 0.2 in. The maximum normal stress that the steel in the wire can withstand is omax = 18 ksi. Will the wire fail? Show your work and your reasoning.

The strut is supported by a pin at C and a steel guy wire AB. The wire AB has a diameter of 0.2 in. The maximum normal stress that the steel in the wire can withstand is omax = 18 ksi. Will the wire fail? Show your work and your reasoning.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Related questions

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure: P = 29.046 kN

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side…

A: When an amount of load act on the object, it has the tendency to change the shape of the object, so…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: H.W2: A rectangular column of sides 0.4m×0.35m, made of concrete, is used to support a compressive…

A: Data given- Rectangular column = 0.4 × 0.35 sides Compressive load = 1.5 MN Diameter of steel rod…

Q: 7. A thick-wall cylinder is made of steel (E-200 GPa and v=0.29), has an inside diameter of 20 mm,…

Q: Determine the required wire diameter

A: To determine the required diameter.

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

Q: A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm.…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine load P that…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure without exceeding either allowable…

Q: The 200 x 200 x 1.250-mm oak (E-12 GPa) block (2) shown is reinforced by bolting two 5x 200 x 1.250…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm2.…

Q: The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α=…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E=…

Q: A 10-m section of steel rail has a cross-sectional area of 7500 mm2. Both ends of the rail are tight…

Q: A thin hollow sphere of radius 300 mm and thickness 2.5 m is subjected to an internal pressure.…

A: Thin spherical shell is given Tensile stress in sphere = σ = 360 kPa Radius of sphere = r = 300 mm…

Q: Three steel plates, each 16 mm thick and width of 300 mm are joined by two 20 mm rivets as shown.…

A: The tensile stress in the rivet system is calculated by the formula given below as- σt=Pw-dt The…

Q: The d = 13-mm-diameter solid rod passes through a D = 20-mm-diameter hole in the support plate. When…

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: Given data: P=9 kipsQ=4 kipsR=18 kipsS=21 kipsσ1=19 ksiσ2=24 ksiσ3=12 ksi Need to determine the…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side…

A: Introduction: A pulley is a wheel with a connected flexible rope, cable, chain, or belt. Pulleys can…

Q: An axial centric force of magnitude P= 410 kN is applied to the composite block shown by means of a…

A: Given data, h= 10 mm. Eb=105 GPa Ea= 70 GPa. P= 410kN.

Q: Rigid bar ABC supports a weight of W = 26 kN. Bar ABC is pinned at A and supported at B by rod (1),…

A: Free body diagram

Q: The 200 x 200 x 1.250-mm oak (E-12 GPa) block (2) shown is reinforced by bolting two 5x 200 x 1.250…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A steel wire 5-m long hanging vertically supports a weight of 1200 N. Determine the required wire…

A: Length of the wire, L=5 mWeight on the wire, P=1200 NStress in the wire limited to, σ=140…

Q: The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is…

A: Draw the diagram of the system.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system P = 9 kips Q = 5 kips R = 20 kips S = 30 kips stress limit in (1) = 19 ksi…

Q: An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34…

Q: The assembly shown below is subjected to the load P applied at 30°. The cylindrical pins at A, B, C,…

Q: The rigid beam BCis supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm?.…

Q: The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical…

Q: Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod (1),…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: A rod is hanging vertically, supports a load of 2000N. Assume the weight of the wire is 1000N,…

A: Given data: P=2000 NF=1000 Nσmax=140 MPa Need to determine the required diameter of the rod.

Q: The homogeneous bar ABCD shown in the Figure is supported - by a Cable that runs from A to B around…

Q: * Your answer is incorrect. The solid circular rod has a cross-sectional area of 410 mm². It is…

A: GivenA=410mm2w=9kN/mP=3kNQ=5kNx=0.5m

Q: Q3) A pillar crane, shown in below, is fastened to the foundation by means of 16 identical bolts…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm2.…

Q: Two identical steel [E = 200 GPa] pipes, each with a cross-sectional area of 2600 mm?, are attached…

Q: 111. A homogeneous 150-kg bar AB carries a 2-kN force as showE in Fig. P-111. The bar is supported…

A: Given:- Weight of bar=150 kg Diameter of cable CD=10mm To find:- Stress in cable

Q: The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying…

Q: A thin hollow sphere of radius 300mm and thickness 2.5m is subjected to an internal pressure.…

Q: Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm…

Q: The force applied at the handle of the rigid lever causes lever to rotate 0.04 radians clockwise…

A: Find the stress in each cable and force applied at point E.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

1. The strut is supported by a pin at C and a steel guy wire AB. The wire AB has a diameter
of 0.2 in. The maximum normal stress that the steel in the wire can withstand is omax =
18 ksi. Will the wire fail? Show your work and your reasoning.
60
200 lb/ft
B
9 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1,80 in. and the compressive force F is 3500 lb. The maximum allowable shear stress t^^, in the wall of the cylinder is 5500 psi. What is the minimum permissible thickness t„± of the cylinder wall? (Sec figure
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.