The table below shows some performance parameters of a certain power transformer.Full-load voltage regulation | Full-load copper loss Load power factor0.5 Lagging5%2 %Zero voltage regulation is obtained at a load power factor of:zeno0.9176 leading0.8 leading0.397 lagging0.703 leading

In this question, Choose the correct options What is power factor to become zero voltage…

The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation | Full-load copper loss Load power factor 5 % 2 % 0.5 Lagging Zero voltage regulation is obtained at a load nower factor of: zenon 0.9176 leading zen 0.8 leading 0.397 lagging 0.703 leading

The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation | Full-load copper loss Load power factor 5 % 2 % 0.5 Lagging Zero voltage regulation is obtained at a load nower factor of: zenon 0.9176 leading zen 0.8 leading 0.397 lagging 0.703 leading

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
An ideal transformer has no real or reactive power loss. (a) True (b) False
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm Regulation of transformer at 0.5 p.f. lagging current The magnetizing current and reactance component of no-load are.........amper , .........ohm The working current and resistance component of no-load are.........amper , .........ohm *
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
6. A single-phase, 225-kVA, 460/120-V transformer has 6% impedance and 96% efficiency. Find its series Rand X in percent and in ohms looking from the HV side source. 7. Determine the rms fanlt currents on both sides of a 100-IVA single nhase
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.