The three water-filled tanks shown are connected by pipes. Preliminary calculations and relevant experience with this scheme lead to estimated values of friction factor, f, as indicated in the figure. Neglect minor losses. a) Determine whether the intermediate reservoir Tank B receives water from Tank A or supplies water to Tank C. Show pertinent solution. b) Find the flow rate in each pipe. Elevation 60 m Elevation = 20 m (B) Elevation - 0 (C) D = 0.08 m { = 200 m f = 0.020 (10) (A) D = 0.10 m - 200 m f = 0.015 D = 0.08 m (- 400 m f 0.020

The three water-filled tanks shown are connected by pipes. Preliminary calculations and relevant experience with this scheme lead to estimated values of friction factor, f, as indicated in the figure. Neglect minor losses. a) Determine whether the intermediate reservoir Tank B receives water from Tank A or supplies water to Tank C. Show pertinent solution. b) Find the flow rate in each pipe. Elevation 60 m Elevation = 20 m (B) Elevation - 0 (C) D = 0.08 m { = 200 m f = 0.020 (10) (A) D = 0.10 m - 200 m f = 0.015 D = 0.08 m (- 400 m f 0.020

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the minor losses (entrance, exit & bend losses) are negligible. Two trials are enough for this exam. -Elevation 35 m Pipe 1: D-0.2m, L=2400m, f=0.020 Elevation 30 m Elevated tank A -Elevation 28 m Elevated tank B Reservoir C Pipe 3: D=0.15m, L=1500m, f=0.020 Pipe 2: D=0.2m, L=2400m, f=0.020 -Elevation 10 m Figure 3
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
2. Determine the discharge in the pipe and pressure at point B. Neglect head losses and assume a = 1 everywhere. Water T 1.5 m 3.5 m 40 cm diameter -20 cm-diameter nozzle
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
Both pipes shown below have a roughness height k, of 0.1 mm and a discharge of 0.1 m /s. D1 = 15 cm, L1 between the tanks? 50 m, D2 = 30 cm, L2 150 m. What is the difference in water-surface elevation Weer 个

pls answer asap for my hydraulics course. A 30 cm diameter pipe is connected by a reducer to a 10 cm diameter pipe. Points 1 (on the 30 cm diam.) and 2 (on the 10 cm diam.) are along the same elevation. The pressure at 1 is 250 kPa. The flow is 30 liters per second and the energy lost between 1 and 2 is equivalent to 20 kPa. Compute the pressure at 2 if the liquid flowing has a specific gravity of 1.50.
2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m, respectively. If the Hazen- Williams Coefficient for all pipes is 110, calculate the flowrate in each pipe. 1 A B 3 2 L₁ = 3000m L2 = 2600m L3 1300m D₁ = 300mm D₂ = 250mm D3 = 200mm
absolute roughness is o.03mm (for both sections), Determine the height H. Neglect local losses. Tip: Losses in pipes connected one after another (as in the figure) they add up 2. Consider the system shown. If the flow is Q = 220 lts / s and the H L=500 m D=45 cm L=800 m D=30 cm
The pipe network shown has the following properties: Li=500m, Di= 250mm; L2=600m, D2=150mm; L3=670m; L=800m, D4=300mm. The flow in line 1 is 0.06m/s and the total head lost from A to D is 10.5 meters. Assume f=0.023 for all pipes. Pipe 2 Pipe 1 Pipe 4 D Pipe 3 a. What is the head lost in pipe 2 in meters? b. What is the flow in pipe 2? c. What is the diameter in pipe 3?
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
Water flows with a discharge of 0,02 through a SG pipe reducer as is shown in the Figure 1. The static pressures at 1st ( Di=0,3m) and 2nd ( D=0,1 m)cross-sections are measured by the inverted U- tube manometer containing oil of specific gravity, SG as 0,7. Determine the manometer reading, h *(m). (1) Water Figure 1
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.