The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to:
Q: Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. Following…
A: Given: Let us consider the given image,
Q: a) Calculate the make up rate of the water by doing a material balance between the water stream and…
A: For set 1 , Mass flow rate of makeup water (m 1 makeup water) = m1 dry air *(ω1 B-ω1 A ) =…
Q: The four bars of Figure A are initially free in the plane, then connecting to bars 2, 3 and 4,…
A: In this problem, we have to choose a generalized co-ordinate system and calculate the degree of…
Q: what would you do if it was a through hole that went all the way through the 6 inch shaft?
A: Given question: what would you do if it was a through hole that went all the way through the 6…
Q: what steps would you take to drill a 0.375 inch hole in a 6 inch long 1 5/8 diamator stainless…
A: Given question: what steps would you take to drill a 0.375 inch hole in a 6 inch long 1 5/8…
Q: A circular specimen with 5 mm diameter is subjected to tensile stress of 31.83 MPa
A: Given that: diameter of the circular specimen = 5 mm Tensile stress = 31.83 MPa It is required to…
Q: d=1.50 in. t=0.875 in. P-7300 lb What is the average bearing stress produced in the support bracket?…
A: Given data: d=1.5 int=0.875 inP=7300 lb Need to determine the average stress produced in the support…
Q: Consider a single server queuing model with Poisson arrivals (2 = 4/hour) and exponential service…
A: GIVEN DATA- ARRIVEAL RATE = 4/hr SERVICE RATE = 4/hr WE HAVE TO FIND PROBABILITY THAT A PERSON WHO…
Q: 2.31 The normal stresses at a point in a steel member are dx = 8 ksi, ay = -4 ksi, and ₂ = 10 ksi.…
A:
Q: In a simple truss, the number of joints, n, and the number of members, m, are related by the…
A: We know that in a simple truss, the number of joints (n), and the number of members (m) are related…
Q: Using your own words Discuss in details the concept of bouncy force and flotation. Discuss the…
A: Concept: Bouncy Force: The upward force which is exerted by the fluid against the weight of…
Q: In an ECM process for machining iron, it is desired to obtain a metal removal rate of 1 cm³/min.…
A: Q=1cm3/minw=56gA=2ρ=7.8 g/cm3f=1609 Amp-min
Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…
A: Given:Net power output, P=80MWP1=10MPAT1=500°CP3=1MPaT3=500°CP4=10KPaηt=0.82ηp=0.95
Q: A specially manufactured Balloon with cylindrical shape has a total mass of M.... kg. The radius of…
A: Given data: M=388 kgd=10 mL=20 mρHe=0.18 kg/m3ρa=1.29 kg/m3 Need to determine the maximum mass the…
Q: 00-kg box is towed to move horizontally from rest by a constant force P=200 N. The kinetic friction…
A: Given:m=100 KgP=200 Nμk=0.1θ=30°g=9.81m/s2
Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…
A:
Q: Compute the position and orientation of the tool point P from the given D-H table for the…
A: Basically, the Position of any object can be seen as the location like we see or use in GPS but the…
Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…
A:
Q: Determine the response of an undamped SDOF system to the force shown in the figure. Show all of your…
A: Given : Mass, m = 3 kg Stiffness, k = 1200 N/m Force, F0 = 300000 N To find : Response of the system
Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…
A:
Q: Injection molding is a process in which a polymer is heated to a highly plastic state and forced to…
A:
Q: pipes in parallel, the total friction head loss equals to the individual friction head loss in each…
A:
Q: A batter hits the baseball A with an initial velocity of vo= 109 ft/sec directly toward fielder B at…
A:
Q: The initial cost of a pickup truck is $10,048 and will have a salvage value of $4,400 after five…
A:
Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…
A:
Q: A and the magnitude of the force N appli
A: θ = 34°θ = 43 deg/sec = ˙0.750492 rad/sθ¨ = 10deg/sec2 = 0.1745 rad/s2m = 0.3 kgL = 0.88 m…
Q: gure 20 m/ 1 of 1 1.5m/ shown Express the coefficients using three significant figures. 197] ΑΣΦ | Η…
A:
Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…
A:
Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…
A:
Q: The truss, shown in figure (3), is being held in place by a pin at H and a roller at A. Use the…
A:
Q: An economizer in a boiler has a flow of water inside the pipes and hot gases on the outside flowing…
A:
Q: 3. A hollow steel shaft used in a construction auger has outer diameter dz-150 mm, and inner…
A: Given:Outer diameter, do=150mmInner diameter, di=100mmShear modulus of elasticity, G=75GPaTorque,…
Q: - A wholeseller supplies 30 stuffed dolls each d e manufacturer in lots of 120 each at 71200 pe O…
A: given:annual demand D=30×250=7500Ordering cost c0=60+250=310carrying cost ch=0.6+(2%×12)of…
Q: Find the spring constant if a 20. N force stretches a spring 2.0 m.
A: GivenF=20N∆=2m
Q: what would be the order of operation to make this part on a virtical mill and what would be the…
A: Note: As you have posted multiple question, i will be answering first question. Please resubmit the…
Q: A sailboat moving in the direction shown is tacking to windward against a north wind. The log…
A:
Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…
A:
Q: 11- The work done by the engine of a 1000 kg car to move it from rest to a speed of 20 m/s is: a- 50…
A: Given data : Speed V=20 m/s Mass m=1000 kg Required : Work done
Q: 8.18 Find the response for the following models. The initial conditions are zero. a. 3x + 21x + 30x…
A:
Q: 25 kips 20 in.- Figure 1 10 in. 25 kips 20 in. B 7.25 in. Sin.- b 1.5 in. 1.5 in.
A:
Q: Discus in details the concepts of: i) Equilibrium of rigid bodies ii) Trusses
A: This question is based on the concept of equilibrium of rigid bodies and trusses.
Q: A skier starts from rest on the 39° slope at time t = 0 and is clocked at t = 2.60 s as he passes a…
A: Given data: θ=39°d=20 mu=0 m/s Need to determine the normal reaction, friction force and coefficient…
Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…
A:
Q: Extrusion is a compression process in which material is forced to flow through a die orific to…
A: Answer True
Q: The sequence of operation are as follows: 1. Activate the lever of the 4/3 DCV to start the process…
A: a) Design the hydraulic circuit with proper labeling including the components required.
Q: Find the force applied Work done=554.44 J Displacement=50 m
A: Given: Work done, W = 554.44 J Displacement, S = 50 m To find : Force applied (F)
Q: a) What is a truss? Explain shortly in your own words, and illustrate with one example.
A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…
Q: The rotation in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 10 mm in radius and…
A: Given: The shaft length, L = 800 mm = 0.8 m The torque applied, T = 80 N.m The radius of shaft, r =…
Q: Explain why modern turbofan engines have more than one stage in the core turbine. Your answer should…
A:
Q: Find the cross sectional area of pipe if discharge through pipe is 333 m3/s and having flow velocity…
A: Given data: ◆ The discharge through pipe: Q = 333 m3/s ◆ The flow velocity through pipe: V = 50 m/s…
Step by step
Solved in 2 steps with 4 images
- For the figure shown determine the reactions at supports A and B, where m1 = 80Kg, and m2 =230 KgThe truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to: h P1 P2 a H B members GH, BG, BC. I P3 G C P4 F D a --- a -- a a) Determine the reactions at the supports A and E. b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint E. d) Using the method of sections, determine forces on members GF GC, CD. e) Using the method of sections, determine forces on P1 Note: You are required to draw the FBD and apply the equilibrium equations for each case. EThe truss in the figure is loaded by four external forces as shown below. Knowing that P1= 30 kN, P2-50 kN, P3=20 kN and P4-60 kN, a= 3 m and h=2 m, you are required to: P2 F a A and F. P1 E G a H I A D a h h B| h P3 P4 a) Determine the reactions at the supports b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint F. d) Using the method of sections, determine forces on members ED, EH, GH. e) Using the method of sections, determine forces on members DC, HC, HI.
- Rigid arm AB is subject to a downward force F=270 lbf. It is supported by asquare shaft journal bearing at A and a cable BC.A. Draw a clear and large free-body diagram (FBD) to show all reaction components on AB. Ifany are not engaged, cross them out and add the note “N.E.” for “Not Engaged.” You do NOTneed to set up any equations or solve for any of the reactions.B. Find the unit vector for cable BC.2) The truss shown in the figure serves to support the deck of a bridge. Draw the FBD of the entire truss and determine the support reactions at A and E. (Show your work). 10 kN 20 kN 30 kN VD 9 m 12 m- -12 m+ -12 m +12 mHSuppose P = 2500 lb. From the frame below, determine the magnitude and direction of the vertical and horizontal reaction (1) at A and D (2) at C as it acts on member BCD
- Question 3. Determine the reactions in the supports A and B and the forces in the members 1, 2 and 3 of the planer truss shown in the figure. P-6 kN, JAD-BD-a-6 m. |AE|-|BC|-b-8 m. E www A Ar 2a 3 B 2P4. Based on the attached figure: (a) Determine the reaction at roller A. A(y) = ? (b) Determine the horizontal and vertical components of reaction at pin B. B(x) = ? , B(y) = ?4.) The uniform 4-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is attached to the midpoint G of the rod as shown in the figure. The rod leans against a frictionless vertical wall at B. Determine the reactions at A and B and the tension in cord CG. [Answer: T = 20.8 N, Ax= -14.7 N (down), Ay= 29.4 N, Az 11.0 N, B= 29.0 N, where the positive answer indicate the reaction goes in the positive direction of the respective axis and vice versa] Hints: Note the given mass from which you need to calculate weight. IF G is is the midpoint of the rod, then the x, y, z coordinates of that point can be taken to be half the x,y,z components of the position vector FAB 150 mm, B 400 mm 0 150 mm 600 m G
- Determine the reactions at supports for the following Figures. A 40 kN/m -8 m B. 3 m 20 KN 150 kN mQ2: For the frame shown below, determine the pin reactions at D and F on member BG? 500N G 3m F 4m 300N D E 4m 3m 3m 3mDetermine the magnitude of the reaction at support A, in kip. If: P = 276 lb, h = 14 in., A = 25 in. b = 9 in.