The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference in the junction temperature, the output changes by 41 micro-Volts. If you have a 32-bit ADC, what is the smallest temperature change you can detect if the ADC range is 10 V? It is 32 bits NOT 16 bit.

The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference in the junction temperature, the output changes by 41 micro-Volts. If you have a 32-bit ADC, what is the smallest temperature change you can detect if the ADC range is 10 V? It is 32 bits NOT 16 bit.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

What is CEMF?
Shown below is a section from the datasheet of 74LS32, a quad 2-input OR chip. What is the noise margin high (in V) of this chip? Limits Symbol Parameter Min Typ Max Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage V 0.8 VIK Input Clamp Diode Voltage -0.65 -1.5 V V VOH Output HIGH Voltage 3.5 V V VOL Output LOW Voltage 0.35 0.5 V 20 μA IH Input HIGH Current 0.1 mA IIL Input LOW Current -0.4 mA los Short Circuit Current (Note 1) -100 mA Power Supply Current Icc 6.2 Total, Output HIGH mA Total, Output LOW 9.8 74 74 74 2.7 -20
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
What is the peak load voltage out of a bridge rectifier for a secondary voltage of 12.6 Vrms? (Use second approximation.) O 16.4 V O 19.2 V O 17.8 V o 7.5 V
2) approximately draw Vout for the circuits below, separately. Point out which one is a rectifier which one is a clipping circuit. Use Vp = 0.7V. Input signal 2tVin 1.5 1 0.5 -0.5 -1 -1.5 -2 Circuit (a) Circuit (b) Vin Vout Vin Vaut R 2 Vonut 1.5 1.5 1 1 0.5 0.5 1 3 4 7 1 2 3 6 7 -0.5 -0.5 -1 -1 -1.5 -1.5 -2, -2
Question 30 The SCR operation characteristic is plotted for Not yet answered O a. la (anode current) vs Ig (gate current), Va (anode – cathode voltage) as a parameter Marked out of 1.00 Ob. P Flag question la vs Va with Ig as a parameter Oc. Ig vs Vg with la as a parameter d. Va vs Ig with la as a parameter
VI Ru Ri Vz I, Io R2 = 3837.79 O. R3 = 3989.3 Q. %3D R4 = 2898.06 Q. V1 = 4.8 V. V2 = 8.1 V. 11 = 0.0099 A Determine the following: a.) The output current lo %3D
The gate current of an SCR full-wave rectifier is adjusted to 1.2mA and the forward breakdown voltage of SCR corresponding to this gate current is 150V. The applied voltage is a sinusoidal voltage of 300V peak, the load resistance is 100 ohms and the holding current is zero. Determine the a) firing angle b) conduction angle c) average output voltage d) average current and e) average power (Our lesson is POWER ELECTRONIC DEVICES, in the lesson of INDUSTRIAL ELECTRONIC)
Describe the function of signal conditioning in this block diagram. 45V A12V thermocouple 50 mV: output driver microprocessor Fan Select one: O a. To convert from analog signal into digital signal. O b. To invert the voltage signal from positive value into negative voltage value. O . To amplify the voltage signal into standard signal so it can be readable by the microcontroller. O d. To isolate the signal between thermocouple and microcontroller
What are IC Voltage regulators? State the different IC voltage regulators and its operation.
Let the values are R1=622.8ohm,R2=915.95 ohm ,The error voltage is =7.9 Volt.and the initial value of output is 5.5 Volt. Vout =
p?attempt=155796&cmid%3D80728 Which device allows current to flow in one direction only? Oa. Resistor O b. Diode O c. Semiconductor O d. Transistor Question 16 Not yet answered P Flag question Marked out of 1.00 Diode used to maintain constant output voltage is PN Junction diode O b. Zener diode Ос. Tunnel diode FUJITSU