The volume of a tetrachloride having a mass of 2498 kg is 0.563 m3. Compute the specific gravity. Round your answer to 2 decimal places.
Q: Inputs: ● ● ● ● F₁ = 9 KN F₂= 2 KN 0 = 30° a = 3 m b=1m At what distance "d" must the resultant…
A: Given data, F1 = 9 KNF2 = 2 KNθ = 30°a = 3 mb = 1m To determine the distance d, for resultant R to…
Q: 8.23 and 8.24 Draw the influence lines for the vertical re- actions at supports A, C, E, and G of…
A: Given data in question Statically determinate beam Span 130 ft Internal hinges To find out ILD for…
Q: What is the uplift pressure head at point P of the weir (junction of floor and pile downstream as…
A: Given data- Uplift pressure heads at Q, R & S- 3.14 m, 2.75 m & 0 m. Rest data are shown in…
Q: During a weekday peak hour, the traffic counts at an intersection approach are: 7:00 a.m. to 7:15…
A: Given, Traffic counts at intersection for weekday To find : PHF and V
Q: A saturated soil has saturated unit weight of 21 kN/m³ and Gs='2.69. Find dry unit weight, void…
A:
Q: Pls
A:
Q: A community had a population of 150,000 in 2010 and it is expected that this will increase to…
A: (a) No change in use rate: Water requirement in 2030 = Population in 2030 * average per capita water…
Q: The stopping sight distance (SSD) for a level highway is 140 m for the design speed of 90 km/h. The…
A: Given that:- Stopping sight distance = SSD = 140 m Design speed = V = 90 km/h Acceleration due to…
Q: A timber pile of length 8m and diameter of 0.2m is driven with a 20 KN drop hammer, falling freely…
A:
Q: 1. Illustrate the loading along BEHK subjected to service dead load of 5 KPa (including its…
A:
Q: Two columns are 5.5 meters away from each other. The dimensions and loads supported by each column…
A: design calculation for the rectangular combined footing: 1.Load calculation:a. Left column: DL + LL…
Q: Analyze the truss structure. Determine all reactions and member forces; for member forces, specify…
A: Given : Required : Analyze the structure
Q: 1. The bar has a cross-sectional area of 400*10-6 m2. If it is subjected to a uniform axial…
A: Given, Cross sectional area, A = 400 x 10-6 m2 or 400 mm2 w = 8 kN/m
Q: Determine the y-coordinate of the centroid of the shaded area shown 7" Parabolic. 3" 0 0 5" -x
A:
Q: Problem 4. Determine the horizontal and vertical reactions at A and C of the two-member frame. 3…
A: Given : Required : Horizontal and vertical reaction at A and C
Q: A flocculation tank with a discharge of 50,000 m³/day and alum dosage is 50 mg/1, Gt=4*104 at a…
A: Answer (1) To design the flocculation tank we need to find depth,width and length of tank Volume of…
Q: Question- The capacity of a single ISA 100 x 100 x 10 mm as tension member connected by one leg…
A: Given- ISA 100×100×10 mm Tension member connected by 1 leg using 6 rivets of 20 mm dia Allowable…
Q: The ultimate BOD of the waste water whose 5 day BOD (BOD), and rate constant (base e) are…
A: Given 5 day BOD=150 mg/L rate constant k=0.23/day Ultimate BOD=?
Q: A post in a rectangle form is subjected to force P. Given the values P = 6969 N, b = 69 mm, h = 96…
A: Given: P = 6969N b = 69mm , h = 96mm and e = 40mm Required : Maximum stress in post
Q: A saturated soil has saturated unit weight of 21 kN/m³ and Gs='2.69. Find dry unit weight, void…
A:
Q: A simply supported beam ABCDEF of 5 m length and load Fig. Find the deflection and slope at point E…
A:
Q: thc
A:
Q: What is 3.785
A: For the given question determine the purpose of the term 3.785 in the solution.
Q: Water (bulk modulus of elasticity = 2.2 x 103 MPa) is flowing with a velocity of 2 m/s through an…
A:
Q: Find the scale for each drawing/model: 1. Drawing length: 9 in. Actual length: 45 ft. 2. Model…
A: Given, Drawing length : 9 in. Actual length : 45 ft. Model length: 6-2/5 or 6.4 m Actual length:…
Q: 5.7 A cable shown in Figure P6.7 supports a uniformly distributed load of 100 kN/m. Determine the…
A:
Q: A right angled triangular notch is used to measure the flow in a flume. If the head measured is 20…
A: Given data- A right angled triangular notch- Measured head H=20 cm=0.20 m, Coefficient of discharge…
Q: Practice Problem: Determine the force P required to start the wedge shown. The angle of friction for…
A: Given Data Angle of friction = 15° Determine the 'P' value to start the wedge.
Q: Draw the 3 Principal Views of the object (given unit in mm, convert it to cm) 51 35 15 25 53 73 20…
A: 3D view of the object is provided. We have to draw three principal views of the object. Three…
Q: Classify the following beams and frames as stable or unstable. If stable, indicate whether…
A:
Q: A distracted driver is travelling at 65mph on a roadway with an upgrade of 4% before he finally…
A: Given, Initial speed, Vi = 65 mph or 95.33 ft/s Grade, G = 4% or 0.04 Rolling resistance factor, frl…
Q: Open Channel Flow - Uniform Flow A penstock of 1 m diameter and 5 km length is used to supply water…
A: Given data- Diameter of penstock d=1 m, Length L=5 km=5000 m. Nozzle diameter dn=15 cm=0.15 m, Head…
Q: A freeway has the following relationship: S = 75.4e- where S' is in mph, for D pc/mi/ln (D<145), b…
A: Free flow relation- S=75.4e-bD (D<145)Vm (capacity) = 2500 pc/h/lnD0=45 pc/mi/lnTo determine -…
Q: 6.8 A cable supports a uniformly distributed load in Figure P6.8. Find the horizontal reaction at…
A:
Q: Draw stress path for the following loading conditions on p-q diagram. 1) 6 = 6, initially, Δό, > 0,…
A: To draw stress path for loading conditions-
Q: What is the flowing-full capacity and velocity for a 500-mm-diameter sewer (n = 0.013) on a slope of…
A: The formula for the full-flowing capacity of a circular pipe is given by: Q = 0.0058 * A * V where Q…
Q: If a point in a strained material is subjected to two mutually perpendicular stresses, 0x = 100 MPa…
A:
Q: Given the figure and the following data: Determine (a) the width of base b on the conditions: a.1…
A: Given:- The unit weight of the concrete = 2.4 T/m3 The coefficient of friction between the base and…
Q: A car follows a slow moving truck (travelling at a speed of 10 m/s) on a two-lane two-way highway.…
A: Given- Speed u=10 m/s Space headway S=16 m Acceleration a=4 m/s2
Q: Given: DL = 385 KN LL= 220 KN f'c = 28 MPa fy = 415 MPa Unsupported Length= 2.80 m K = 1.00…
A: Answer Since we are given only axial loads. Let us design the column considering concentrically…
Q: If the coefficient of friction between the steel wedge and the moist fibers of the newly cut stump…
A: The maximum angle at which the wedge may be driven into the wood can be calculated using the formula…
Q: For the beam shown in the following diagram, draw the shear force and bending moment diagrams. Rigid…
A: Given: Required: To calculate support reactions using moment around D
Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filter are 55%,…
A: Given that :- In an aggregate mix, Proportions of coarse aggregate = W1% = 55% Proportions of fine…
Q: A soil has a bulk density of 22 kN/m³, water content 10%, the dry density of soil is - 1. 18.6 kN/m³…
A: Given Unit weight=22 kN/m3 water content w=10% Dry density=?
Q: For the beam and loading shown, determine the deflection at point C in (mm). Indicate the negative…
A: Given Data E = 200 GPA = 200 × 103 N/mm2 Determine the deflection at point-C. Note:- For…
Q: Ao 3 KN VB C 6 kN VD E -1.26 m-1.26 m-1.26 m 1 kN /F ↑ 1.2 m G 2. Determine the force in each member…
A:
Q: A steel cable of 2 cm diameter is used to lift a board 500 kg. Given that the length of the cable is…
A: Given data- A steel cable- Diameter d=2 cm, Load P=500π kg, Length of cable L=10 m=1000 cm, Young's…
Q: Solve the shear and moment diagram using the equation method
A: Given Data Draw shear force and bending moment diagram using equation method.
Q: Determine the polar radius of gyration about point A for the shaded area shown. 74 mm 74 mm 57 mm…
A: Given Sides of square = 74 mm Radius of quarter Circle= 57 mm
Q: The hydrostatic stress for the state of stress represented by σij given below is MPa 50 50 125 75 75…
A: Given- State of stress given- σ11=100,σ22=125,σ33=75 It is needed to find the hydrostatic stress.
The volume of a tetrachloride having a mass of 2498 kg is 0.563 m3. Compute the specific gravity.
Step by step
Solved in 2 steps with 2 images
- 1. As shown, a cube (L 60 mm) suspended in carbon tetrachloride (S is exactly balanced by an object of 1.59) mass m1 700 g. Find the mass m2 of the cube. (20 points) Balance beam scale Cube with mass Block with mass Carbon tetrachioride500 lb 200 lb 300 lb В E 6 ft- - 4 ft 4 ft 6 ft 2 ft a. Value of RA=?2. A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and water, as shown. a. Find the specific gravity of the material. b. How much weight is required to fully sSubmerge the cube under water? (SG=0.973) (0.063 lb) Kerosene b/3 Water 2b/3 b- APIL
- A tank of carbon tetrachloride has a mass of 784 kg and a volume of 0.481 m3. What is its specific gravity? Round off to two decimal places.Your answer is partially correct. An aluminum-alloy rod has a length of 8.1814 cm at 14.00°C and a length of 8.1942 cm at the boiling point of water. (a) What is the length of the rod at the freezing point of water? (b) What is the temperature if the length of the rod is 8.1916 cm? th (a) Number i 817.931 Units cm (b) Number 82.5318 Units °CQuestion 6 (of 8) 6. The density of platinum is 21500 kg/m³ and that of aluminum is 2702 kg/m³. Find the ratio of the volume of 1.80 kg of platinum to the volume of 1.17 kg of aluminum.
- The radius and length of a steel cylinder are 60 mm and 120 mm, respec-tively. If the mass density of steel is 7850 kg/m3, determine the weight of thecylinder in pounds.1. What is the weight of 1 ft³ of carbon tetrachloride (SG = 1.59) in Newtons?A piece of irregular shaped metal weighs 300 N in air. When the metal is completelysubmerged in water, it weighs 232. 2 N. Find the volume of the metal
- 2. A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and water, as shown. a. Find the specific gravity of the material. b. How much weight is required to fully submerge the cube under water? (SG=0.973) (0.063 lb) Kerosene b/3 Water 2b/3 PIEA 325 L of carbon tetrachloride weighs 500 kg. a. Calculate its density. b. Calculate its specific weight c. Calculate its specific gravity.Question- Metal body floats at the interface of water and oil of SG=0.85 such that 35% of its volume is submerged in water and 65% in the oil. What will be the density of the metal approx.