The water table in a deposit of sand 8 m thick, is at a depth of 3 m below the surface. Above the water table, the sand is saturated with capillary water. The total and effective stress (in kN/m²) at point A as shown in figure are: 8m 3m 1m a. 19.62, 19.62 b. 39.24, 39.24 c. 39.24, 19.62 d. 19.62, 39.24 Sand (Capillary Saturated) Ysat = 19.62 kN/m³

The water table in a deposit of sand 8 m thick, is at a depth of 3 m below the surface. Above the water table, the sand is saturated with capillary water. The total and effective stress (in kN/m²) at point A as shown in figure are: 8m 3m 1m a. 19.62, 19.62 b. 39.24, 39.24 c. 39.24, 19.62 d. 19.62, 39.24 Sand (Capillary Saturated) Ysat = 19.62 kN/m³

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter14: Lateral Earth Pressure

Section: Chapter Questions

Problem 14.2P

See similar textbooks

Similar questions

4m 7.16 For each of the cases I, II, and III of Fig. P7.16, determine the pressure, elevation, and total head at the entering end, exit end, and point A of the sample. (After Taylor, 1948.) 4m 4 m 5 + Dll. Case I FIGURE P7.16 1m Dll. Case II 1 m 4m- Case III 1 m D
100 KN 150 KN 4.00 meters 5.00 m 4.00 meters 2.00 meters 2.00 meters Joint Horizontal Component Vertical Component A E Member Magnitude ВС BD
250 kN 250 kN 250 kN B D E 0.9 m 0.9 m 0.9 m 0.9 m Fig. P8.5
Analyse the continuous beam shown in fig. 5 by stiffness matrix method. 5 kN/mx Las 1.5, EI ←— 6m B fig. 5 3m 12 kN ↓ с 2 EI +++ 2m +
A sandy soil has a drained angle of friction of 32°. The deviation stress at failure is 400 kPa. 13. Compute the angle that the failure plane makes with the major principal plane. a. 63° b. 64° c. 61° d. 60° 14. Compute the chamber confining pressure in kPa. a. 174.61 b. 177.42 c. 103.40 d. 170.50 15. Compute the shear stress in kPa at the point of the failure plane. a. 127.21 b. 339.22 c. 201.60 d. 169.61
5. A flat plate is sliding at aconstant velocity of 5 m/s on a large horizontal table. A thin layer of oil ( of absolute viscosity 0.4 N.s/m2) separates the plate from the table. To limit the shear stress in the oil layer to 1 kpa, the thickness of the oil film (mm) should be most nearly to a) 0.2 b) 20 c) 1.6 d) 1.85
A simply supported beam 120 mm wide, 180 mm deep and 6 m long carries a uniformly distributed load of 4 kN/m.1. Compute the horizontal shearing stress developed at layer 30 mm from top for a section1 m from the left end. a. 309 kPa b. 494 kPac. 555 kPad. 645 kPa2. Compute the horizontal shearing stress developed at layer 90 mm from top for a section1 m from the left end. a. 345 kPab. 494 kPac. 555 kPad. 645 kPa3. Compute the maximum shearing developed in the beam. a. 671 kPab. 833 kPac. 584 kPad. 781 kPa
The water table in soil deposit is 2 m below the ground surface. The soil above the water table has dry unit weight of 14.85 kN/m3. The saturated unit weight of the soil is 20.58 kN/m3. Determine the total vertical stress at a point 4.8 m below the ground. CHOICES A. 88.63 kPa B. 89.68 kPa C. 90.45 kPa D. 87.32 kPa
= A soil profile at a site consists of a 5 m of gravelly sand (ysat = 18.5 kN/m³; ym 17.0 kN/m³) layer underlain by 4 m of sandy gravel (Ysat = 18.0 kN/m³). The water table is 4 m below the ground level. Plot the variation of ov, o'v, and u with depth. Neglect the capillary effects.
| 166 kPa 54 kPa x 33 kPa Stresses on a x-y Cubic Element in the 0₁-03 plane. Questions 4-10 Draw Mohr's Circle for the stress condition shown above to answer the questions.
Air fl ows at supersonic speed toward a compression ramp,as in Fig. . A scratch on the wall at point a creates awave of 30° angle, while the oblique shock created has a508 angle. What is (a) the ramp angle θ and (b) the waveangle ϕ caused by a scratch at b?
9.48 Water flows past a triangular flat plate oriented parallel to the free stream as shown in Fig. P9.48. Integrate the wall shear stress over the plate to determine the friction drag on one side of the plate. Assume laminar boundary layer flow. U = 0.2 m/s 1.0 m 45