There is a circular gate at the end of the tank as illustrated. A 6.387 * 10-3 m³ wood block is tied to the end of the gate as illustrated. Density of the wood block is 0.6 g/cm³ . Water is at 15.6 °C and Mercury is at 20 °C. What will be the reading h approximately on the mercury manometer on the left side when the gate opens up? Water 50 Wood

There is a circular gate at the end of the tank as illustrated. A 6.387 * 10-3 m³ wood block is tied to the end of the gate as illustrated. Density of the wood block is 0.6 g/cm³ . Water is at 15.6 °C and Mercury is at 20 °C. What will be the reading h approximately on the mercury manometer on the left side when the gate opens up? Water 50 Wood

Name: There is a circular gate at the end of the tank as illustrated. A 6.3
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: There is a circular gate at the end of the tank as illustrated. A 6.387 * 10–3 m³ wood block istied to the end of the gate as illustrated. Density of the wood block is 0.6 g/cm³. Water is at15.6 °C and Mercury is at 20 °C. What will be the reading h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5 A U-tube manometer similar to that shown below is used to measure the gauge pressure of water (mass density p = 1000 kg /m3). If the density of mercury is 13.6 x 103 kg /m³, what will be the gauge pressure at A if h1 = 0.45 m and D is 0.7 m above BC. Wwater Wmercury
The pressure of the natural gas installation is as follows.As you can see, mercury (mercury), oil (oil) and water (water) fluidsIt is measured with a manometer. Open end of the manometer (X + 85)It is under the influence of kPa ambient pressure. The relative content of mercury and oil (relative to water)density (SG) and density of water (ρwater = 997 kg / m3) is known.Determine the absolute pressure in the installation (X=00)
As shown in the figure, an inclined manometer is used to measure the pressure of the gas within the reservoir. The manometer fluid is mercury, which has a density of 845 Ib/ft3. The manometer fluid rises a distance d = 12 inches along the manometer tube, which is inclined e = 20° from the horizontal. The atmospheric pressure is 14.7 Ibf/in? and the acceleration of gravity is 32.2 ft/s?. Patm = 14.7 Ibf/in.? Gas reservoir g = 32.2 ft/s? a 20 in. Mercury (p = 845 Ib/ft³) Determine the gas pressure, in Ibf/in?. Express the pressure as a gage or a vacuum pressure, as appropriate, in Ibf/in2.
The tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40 degrees C. If agauge pressure on the tank reads 7.5 bars,what is themass of the air in the tank?
A cylinder contains a fluid at a gauge pressure of 350kPa. Express the pressure in terms of the column height of (a) water (p 1000kg/m") (b) Hg (S = 13.6). What would be absolute pressure in the cylinder if the atmospheric pressure is 101.3 kPa ?
An air-filled, hemispherical shell is attached to the ocean floor at adepth of 10 m as shown in fig. A mercury barometer located inside the shell reads 765 mmHg (absolute pressure inside the shell)m, and a mercury u-tube manometer designedto givethe outside water pressure indicates differential reading of 735 mmHg as illusrated. Based on these data,what is the atmospheric pressure at the ocean surface for seawater (SG=1.03)
Consider a U-tube manometer used to measure the density Pa of liquid A, as shown below. Mercury is used as the base liquid for the manometer with density Phg = 13600kg/m³. If hng = 5mm and ha = 22.4 mm, find Pa. ha Pa U Phg hng
The capillary rise and fall in the glass tube used for both measuring water level and mercury level is not to exceed 0.8mm and 0.3mm respectively. Determine the minimum size of a glass tube for both liquids, given that surface tension of water = 0.082N/m and surface tension of mercury= 0.52 N/m with diagram. MODEL QUESTION PAPER
The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in the figure. For the given fluid heights and specific gravities, calculate the pressure difference AP= PB - PA. The specific gravities are 13.5 for mercury, 1.26 for glycerin, and 0.88 for oil. Take the standard density of water to be pw=1000 kg/m³. The heighth of mercury in the manometer is 25 cm. Water SG=1.0 Mercury SG= 13.5 55 cm The pressure difference is Glycerin SG=1,26 10 cm 12 cm Oil SG=0.88 kPa.
A U-tube mercury manometer is used to measure the pressure at a pointon the wing of a wind-tunnel model. One side of the manometer isconnected to the model, and the other side is open to the atmosphere.Atmospheric pressure and the density of liquid mercury are1.01 × 105 N/m2 and 1.36 × 104 kg/m3, respectively. When thedisplacement of the two columns of mercury is 20 cm, with the highcolumn on the model side, what is the pressure on the wing?
Bottle was filled with water and a hole is punched in the bottle.When the bottle is closed, water does not come out of the hole. However, when the bottle is open, water comes out of the hole. Other information would be - Atmospheric pressure is 1 atm (101325 Pa) - Assume bottle is 20 cm and the hole is on the 10 cm above the bottom of the bottle (use it as reference level) Define the pressure(s) acting at the hole when the bottle is open and calculate total pressure. Define the pressure(s) acting at the hole when the bottle is closed and calculate total pressure. Using the results from part a and b, why does water come out when the bottle is open and why does not it come out when the bottle is closed?
A and B are cross-sections of two pipes with water flowing. These pipes look like To measure the pressure difference between A and B by connecting a U manometer is requested. The heights in the U manometer are given in inches (1 inch=25.4mm). Since Moil=850 kg/m3 and 'mercury=13600 kg/m3 A- Find the pressure difference B. B Oil 8 -H20 10 H20 4 3 Hareketli plaka -Hg-