This time the loop has constant area 0.530 m^2, and the magnetic field has constant strength 0.470 T. This time we re going to achieve an induced voltage 0.216 V by rotating the loop through a 90 degree angle. How much time must it take for the loop to complete this 90 degree turn? O1.15 s O 0.35 s O 0.92 s O 1.38 s

This time the loop has constant area 0.530 m^2, and the magnetic field has constant strength 0.470 T. This time we re going to achieve an induced voltage 0.216 V by rotating the loop through a 90 degree angle. How much time must it take for the loop to complete this 90 degree turn? O1.15 s O 0.35 s O 0.92 s O 1.38 s

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter12: Sources Of Magnetic Fields

Section: Chapter Questions

Problem 71AP: How is the percentage change in the strength of the magnetic field across the face of the toroid...

See similar textbooks

Similar questions

How many turns must be wound on a flat, circular coil of radius 20 cm in order to produce a magnetic field of magnitude 4.0105 T at the center of the coil when the current through it is 0.85 A?
How is the percentage change in the strength of the magnetic field across the face of the toroid related to the percentage change in the radial distance from the axis of the toroid?
A square loop whose sides are 6.0-cm long is made with copper wire of radius 1.0 mm. If a magnetic field perpendicular to the loop is changing at a rate of 5.0 mT/s, what is the current in the loop?
A 0.50-kg copper sheet drops through a uniform horizontal magnetic field of 1.5 T, and it reaches a terminal velocity of 2.0 m's. (a) What is the net map,-, eh: force on the sheet after it reaches terminal velocity? (b) Describe the mechanism responsible for this force, (c) How much power is dissipated as Joule heating while the sheet moves at terminal velocity?
Two flat, circular coils, each with a radius R and wound with JV turns, ace mounted along the same axis so that they are parallel a distance d apart. What is the magnetic field at the midpoint of the common axis if a current I flows in the same direction through each coil?
, (a) At what angle 0 is tlie torque on a current loop 90.0% of maximum? (b) 50.0% of maximum? (c) 10.0% of maximum?
Two long, parallel wires each carry the same current I in the same direction (Fig. OQ30.4). Is the total magnetic field at the point P midway between the wires (a) zero, (b) directed into the page, (c) directed out of the page, (d) directed to the left, or (e) directed to the right?
The magnetic field perpendicular to a single sire loop of diameter 10.0 cm decreases fron 0.50 T to zero. The re Is made of copper and has a diameter of 2.0 mm and length 1.0 cm. How much charge moves thrnugh the re while tt field is changing?
A 500-turn coil with a 0.250m2 area is spun in Earth’s 5.00105T magnetic field, producing a 12.0-kV maximum emf. (a) As what angular velocity must the coil be spun? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?
Within the green dashed circle show in Figure P30.21, the magnetic field changes with time according to the expression B = 2.00t3 4.00t2 + 0.800, where B is in teslas, t is in seconds, and R = 2.50 cm. When t = 2.00 s, calculate (a) the magnitude and (b) the direction of the force exerted on an electron located at point P, which is at a distance r = 5.00 cm from the center of the circular field region. (c) At what instant is this force equal to zero? Figure P30.21
Review. A rod of mass 0.720 kg and radius 6.00 cm rests on two parallel rails (Fig. P28.23) that are d = 12.0 cm apart and L = 45.0 cm long. The rod carries a current of I = 48.0 A in the direction shown and rolls along the rails without slipping. A uniform magnetic field of magnitude 0.240 T is directed perpendicular to the rod and the rails. If it starts from rest, what is the speed of the rod as it leaves the rails? Figure P28.23 Problems 23 and 24.
Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor, and the circuit is completed by a bar that is free to slide on the rails (Fig. P32.71). A uniform magnetic field of 5.00 T directed out of the page permeates the region, a. What is the magnitude of the force Fp that must be applied so that the bar moves with a constant speed of 1.25 m/s to the right? b. What is the rate at which energy is dissipated through the 2.00- resistor in the circuit?