Three idlers of 28 T , 26 T and 26 T are introduced between the 34 T pinion withaturning speed of 400 rpm driving a final 96T gear. A. What would be the final speedof the driven gear and its direction relative to the driving gear rotation? B. computecompute the center distance between driving and driven gears if the module is 5

Three idlers of 28 T , 26 T and 26 T are introduced between the 34 T pinion withaturning speed of 400 rpm driving a final 96T gear. A. What would be the final speedof the driven gear and its direction relative to the driving gear rotation? B. computecompute the center distance between driving and driven gears if the module is 5

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter38: Manual Transmissions And Transaxles

Section: Chapter Questions

Problem 5ASRQ: Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of...

See similar textbooks

Similar questions

Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly at 100 RPM. Minimum number of teeth can not be less than 20 and the maximum numbor of teeth can not be more than 150. The speed of goar B must be exactly 500 RPM. Determine tho speed of gear C: Note: This is a short answer type question with limited space for answer. Therefore, write the answors and do not show any other details. Input pinion A N= 20 teeth W,= 1,500 rpm No B
3. For the system shown below. The INPUT gear has 15 teeth, the IDLER and the OUTPUT gear has 60 teeth. Solve for the GEAR RATIO. INPUT IDLER OUTPUT
A simple gear train has 2 spur gears. The input gear has 23 teeth and the output gear has 93 teeth. The input rotates at 1,983 rev/min clockwise. Calculate the gear ratio and the output speed in rev/min.
Using the data below, calculate the following for all gear settings and list the results in a table form: The speed ratio of the MM245 Automotive gearbox. The input and output torque. The input and output power. The efficiency of the gear system. Gears Input Speed (rpm) Output Speed (rpm) Input Torque (N.m) Output Torque (N.m) 1 322 97 2,67 0,72 2 320 168 3.05 1,23 3 311 238 4,24 1,83 4 297 297 5,95 2,36 5 280 334 7,36 2,80 The moments of inertia of the parts attached to the input shaft A is 0.019 kgm2 and that of the parts attached to output shaft B is 0.1 kgm2. If input shaft A exerts a constant torque of 7.27 Nm and is geared to output shaft B, calculate the following: The gear ratio gives the maximum angular acceleration of output shaft B. The corresponding angular acceleration of each shaft.
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
Speed ratio of compound gear train is ratio between speed of driver to speed of driven. Select one: O True O False
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate
Industrial Maint. What are the direction and speed of the driver gear (D1) in Figure 6-40 if the driven gear (D2) is a 2 in. gear, D1 is a 12 in. gear and D2 is rotating at 1248 rpm (CW)? see picture
2. Design a compound gear drive for an exact velocity ratio of150:1
Figure 1 shows a stage 1 to stage 2 compound gear train through from Gears A, B, C to D. If the input shaft rotates at 650 revolutions per minute (rpm), calculate the angular velocity (ω) in rad/s at the output shaft of the compound gear train. See below for the number of teeth for Gears A, B, C & D. Gear A: 22 TeethGear B: 48 TeethGear C: 30 TeethGear D: 70 Teeth
Q1: Based on the gear train given in below figure with 1000 rpm input speed, calculate the output rpm (rev/min)? (Input gear – 1 and output gear – 4). N = 30 teeth N, = 55 teeth N= 55 teeth 2-3 N3 = 30 teeth 4 Compound gear 3 Input - Output
Figure 1 shows a stage 1 to stage 2 compound gear train through from Gears A, B, C to D. If the input shaft rotates at 650 revolutions per minute (rpm), calculate the angular velocity (ω) in rad/s at the output shaft of the compound gear train. See below for the number of teeth for Gears A, B, C & D. Gear A: 22 TeethGear B: 48 TeethGear C: 30 TeethGear D: 70 Teeth (show all work)