Three resistors, R, 2R, and 3R, where R = 18.8 , are wired to an inductor, L = 0.255 H, an emf, ε = 44.7 V, and a switch as shown in the circuit diagram. Assume the direction of the three currents, 11, 12, and 13, are as indicated in the diagram. 1. Just Closed (1 of 2) (a) What is the current through the inductor immediately after the switch is closed? |L= (b) Write symbolic expressions for the current through resistors R and 2R immediately after the switch is closed, in terms of R, E, and L, as needed, plus constants, then calculate each numeric value. 4₁ = 1₂ = E 3R ε 3R 3R 3R = 0.793 0.793 0.793 A✔ S 0.793 A✔✔ 2R 3R I3 000

Three resistors, R, 2R, and 3R, where R = 18.8 , are wired to an inductor, L = 0.255 H, an emf, ε = 44.7 V, and a switch as shown in the circuit diagram. Assume the direction of the three currents, 11, 12, and 13, are as indicated in the diagram. 1. Just Closed (1 of 2) (a) What is the current through the inductor immediately after the switch is closed? |L= (b) Write symbolic expressions for the current through resistors R and 2R immediately after the switch is closed, in terms of R, E, and L, as needed, plus constants, then calculate each numeric value. 4₁ = 1₂ = E 3R ε 3R 3R 3R = 0.793 0.793 0.793 A✔ S 0.793 A✔✔ 2R 3R I3 000

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

What is the current in the inductor ILO in continuity mode before opening the switch. 192 Select one: O a. ILO = 2 A O b. IL00 A O C. ILO = 3 A O d. IL0 = 4 A 2 V 192 k ILO 0.5 H
The symbol shown is a a. polarized capacitor. b. normally closed switch. c. normally open held closed switch. d. normally open contact.
* For the Photoflash unit, R1=5KQ, C=1500 uf R2= 120. The time required for the capacitor to fully charge is High voltage dc supply R₁ 1 2 R₂ C 32 SO O 30.5 S 37.5 S 50 S 60 S O
Capacitor has the ability to store a quantity of a. Dynamic Electricity b. Dielectric c. Electric Flux O d. Static electricity
Refer to the figure below. a) Explain the function of the 7.5 – kilo Ohm resistor and the 0.2 micro Farad capacitor. b) What is the function of the circuit (you may explain its basic operation and the expected output)? 5V 7.5kn OUT3 Output RST 커 DIS THR LM555CM TRI CON 0.1uF-POL GND |1 0.001 µF Trigger Input
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
1. Is it expected that the clamping action produced by the circuit of Figures 1 and 3 if the oscilloscope input coupling were set to AC? Why or why not? Vin 1 μF FF R₁ D₁ 120 ΚΩ 1N4148 1 F ww R₁ 120 ΚΩ +12 V R₂ 51 ΚΩ Q₂₁ 2N2222 41₁ Vout Vout (Ctrl)
QUESTION 1 If a multiratio CT having 150:5 CT ratio with 0.104 ohm secondary resistance and the excitation current 0.2 A, I -SA Za1 ohm. a) Find the primary side of the CT and show the details of your work. b) Find the CT error and show the details of your work.
Why is it desirable to wait 1 s after a potential pulse before recording the current in voltammetry?
The Insulator has a very small energy gap ? True O False O
The Value of R1 is 39.4Ohms. explain
0.5) A full-wave rectifier with L-C filter is shown in figure 3. If the resistance of the load is 2002, detemine the ripple factor. 100mH 52 Vs 470 µF RL Vs = v2 5 Sin 314t %3D