TmaXLiquidusmgAll LiquidA LiquidB+LiquidTTEA+B (all solid)SolidusAFigure 1Study the following terms and phase diagram, fill in the blanks as indicated.Refer to the figure above.Melting point is a physical property of a pure organic solid and is defined as the temperature at whichthe vapor pressure of the solid and liquid are equal. A pure solid melt reproducibly over a narrow rangeof temperatures.Above is a two-component phase diagram for two hypothetical compounds A and B.а.indicates the melting point of pure solid A.b._indicates the melting point of pure solid B.С._indicates the melting point of a 80:20 mixture of A and B respectively.d.indicates the melting point of a 55:45 mixture of A and B respectively.Eutectic composition is a mixture of compounds with a specific chemical composition that solidifies at alower temperature than any other composition.е._indicates the eutectic temperature for these two compoundsf.A:B indicates the composition of A and B whereby the eutectic temperature is observed.

Answered: Image /qna-images/answer/e3271e30-0715-46e3-942f-9dd1a8f8c62d.jpg

Tma X Liquidus mg All Liquid A Liquid B+Liquid TE A+B (all solid) Solidus A Figure 1 Study the following terms and phase diagram, fill in the blanks as indicated. Refer to the figure above. Melting point is a physical property of a pure organic solid and is defined as the temperature at which the vapor pressure of the solid and liquid are equal. A pure solid melt reproducibly over a narrow range of temperatures. Above is a two-component phase diagram for two hypothetical compounds A and B. indicates the melting point of pure solid A. a. b. indicates the melting point of pure solid B. C. _indicates the melting point of a 80:20 mixture of A and B respectively. d. indicates the melting point of a 55:45 mixture of A and B respectively. Eutectic composition is a mixture of compounds with a specific chemical composition that solidifies at a lower temperature than any other composition. е. _indicates the eutectic temperature for these two compounds f. A: B indicates the composition of A and B whereby the eutectic temperature is observed.

Tma X Liquidus mg All Liquid A Liquid B+Liquid TE A+B (all solid) Solidus A Figure 1 Study the following terms and phase diagram, fill in the blanks as indicated. Refer to the figure above. Melting point is a physical property of a pure organic solid and is defined as the temperature at which the vapor pressure of the solid and liquid are equal. A pure solid melt reproducibly over a narrow range of temperatures. Above is a two-component phase diagram for two hypothetical compounds A and B. indicates the melting point of pure solid A. a. b. indicates the melting point of pure solid B. C. _indicates the melting point of a 80:20 mixture of A and B respectively. d. indicates the melting point of a 55:45 mixture of A and B respectively. Eutectic composition is a mixture of compounds with a specific chemical composition that solidifies at a lower temperature than any other composition. е. _indicates the eutectic temperature for these two compounds f. A: B indicates the composition of A and B whereby the eutectic temperature is observed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A substance exists in two solid modifications alpha and beta and also as liquid and vapour at a pressure of 1 atm alpha melts at a lower temperature to form liquid. Also alpha is denser than the liquid but beta is less dense than the liquid assuming that no meta stable equilibria are observed sketch p-t phase diagram show the significance of each point,line and region also show all triple points.
100 atm 1 atm 0.118 atm 114 °C 184 °C 535 °C Temperature (not to scale) a.) Use the above generic phase diagram, clearly identify where you would find the following: Gas, Liquid, Solid, Triple Point, Draw arrows and label to indicate the six transitions (melting, freezing, sublimation, deposition, vaporization and condensation) b.) Based on the above phase diagram, what phase would you be in at a pressure of 50 atm and 300°C? c.) Based on the above phase diagram at what temperature in °C would vaporization occur under normal conditions? d.) If the pressure was 0.050 atm and 425°C, what phase would you be in? e.) If the pressure was 0.118 atm and temperature was 114°C, what phase(s) would you be in? f.) At approximately what temperature would the normal freezing point be in °C? g.) If the pressure was 0.105 atm and starting at a temperature of 32°C to 450°C what phase changes would occur (put in increasing temperature order). Pressure (not to scale)
1. Visualize a substance with the following points on the phase diagram: a triplepoint at 0.05 atm and 150 K; a normal melting point at 175 K; a normal boiling pointat 350 K; and a critical point at 2.0 atm and 450 K. The solid liquid line is “normal”(meaning positive sloping). For this, complete the following:a. Roughly sketch the phase diagram, using units of atmosphere and Kelvin. Labelthe area 1, 2, and 3, and points T and C on the diagram.b. Describe what one would see at pressures and temperatures above 2.0 atmand 450 K.c. Describe the phase changes from 50 K to 250 K at 1.5 atm.d. What exists in a system that is at 1 atm and 350 K?e. What exists in a system that is at 1 atm and 175 K?2. Based from the phase diagrams of water and carbon dioxide, answer thefollowing questions and justify your answers: 1. You have ice at 263 K (-10.0 oC)and 1.0 atm. What could you do to make the ice sublime? 2. A sample of dry ice(solid CO2) is cooled to 173 K (-100.0 oC), and is set on a table at…
The following is a hypothetical binary phase diagram with various temperatures highlighted as (T) where n corresponds to a numeric value. Use the diagram to L T2 answer the following questions: 1. How many solid phases are there in the T4 diagram? Ans.:_ 2. Identify the melting point of A & B? Ans: m, is & mg is T7 3. How many invariant points are there? Write To the reactions. Tu A WB Temperature to
Hi, I need help with this problem.Derive and evaluate the Clausius-Clapeyron equation for the Solid-Liquid state and the Solid-Vapor state, as tip told us that in short words construct the phase diagram from a triple point of water and the critical temperature.And that we do it either in Excel or Mathlab, but I can take care of that myself considering how to start I hope you can support me.
In the region indicated with arrows in the phase diagram shown below (above the upper line), which of the following statements are true: 1300 - L (liquid) O b. O C. T(°C) 1200 20 30 ↑ wt% Ni 40 There are solid grains mixed with a liquid phase There is no solid fraction in the material liquidus solidus α (solid) Select one or more: a. The proportion of alpha phase increases going from right to left at a fixed temperature. 50 Od. The proportion of "L" phase increases going from right to left at a fixed temperature O e. The composition of the phase is pure liquid
help pls A two-phase phase diagram is shown. Answer the following questions t -1300 1500+ Temperature 1100 0 34 54! 166 482 80 Composition of Ni % 20 What is the composition (in % Cu) of the solid phase corresponding to the red dot in between the solidus and liquidus lines in the phase diagram? Just write the number. Do not write the % symbol. Question 17 2.33 100 An alloy is being made with 66% Ni and 34% Cu. When it is cooled from 1500°C to the temperature corresponding to the red dot in the phase diagram, how many kg of liquid is present in the mixture?
Given a blank phase diagram, label the solid, liquid, and gas phases for a pure substance. Give the approximate temp. and pressure of the triple point, and determine what the substance's phase would be at a given temperature and pressure. Can you provide an example?
Exercises: Sketch the phase diagram of a substance with the following points on the phase diagram: a triple point at 0.5 atm and 150 K; a normal melting point at 175 K; a normal boiling point at 350 K; and a critical point at 2.0 atm and 450 K. The solid liquid line is “normal” (meaning positive sloping). 1. Label the area 1, 2, and 3, and points T and C on the diagram. 2. Describe what one would see at pressures and temperatures above 2.0 atm and 450 K. 3. Describe the phase changes from 50 K to 250 K at 1.5 atm. 4. What exists in a system that is at 1 atm and 350 K? 5. What exists in a system that is at 1 atm and 175 K? Sketch the cooling curve of a substance with the following points: (A) 85 OC and 0 min, (B) 60 OC and 2 min, (C) 60 OC and 5 min, (D) 20 OC and 8 min, and (E) 20 OC and 11 min. Label each line 1, 2, 3, and 4 and each point A, B, C, D, and E. 1. What phase(s) exist at each of the numbered sections? 2. At what…
How do you call in binary phase diagram, the line which is described as the locus of all system that represent the boundary between a single liquid phase and the two phases? Liquidus Eutectic point Critical point Triple point
Use the phase diagrams for Cu-Ni and Cu-Ag systems below to answer the question: Use the diagrams provided to determine the values of the following: i. Solubility of Ni in Cu at 1050 °F. ii. Solubility of Ag in Cu at 700 °F.iii. Solubility of Cu in Ni at 1300 °F. iv. Solubility of Cu in Ag at 400 °F.
At what temperature does the first liquid phase form at 90% Ni? T(°C) 1600 1500 1400 1300 1200 1100 1000, L (liquid) L+α solidus liquidus 80 100 20 40 60 80 wt% Ni