answer quickly To decrease efficiently a supersonic flow to a subsonic flow via shock systems, you decide to comparethe loss in total pressure in each of the shock systems. Therfore, you consider airflow at M1 = 4,P1=1 atm in the following cases.a) A single normal shock wave.b) An oblique shock with a deflection angle of 25.3°, followed by a normal shock.c) An oblique shock with a deflection angle of 25.3°, followed by a second oblique shock of deflectionangle of 20°, followed by a normal shock.Which of the three shock systems results in a small possible loss in total pressure? what canyou infer about the efficiency of the various shock systems?

Answered: Image /qna-images/answer/128bd80f-e288-497d-ab1d-bb1e7f80082f.jpg

Answered: To decrease efficiently a supersonic…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ Answer the following: 1) Separation in flow past a solid object is caused by (a) a favourable (negative ) pressure gradient (b) an adverse ( positive ) pressure gradient (c) the boundary layer thickness reducing to zero 2) In the design, we have to delay the separation point in order to reduce wake size (T/F) 3) Define Mach number, boundary layer and shock wave. 4) when the flow is accelerates if the cross sectional area is increases (a) M 1 (c) M =1
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (i) In analysing this nozzle using the 1st law of thermodynamics,the change in which type of energy is negligible? (ii) Determine the density and velocity of the air entering thenozzle. (iii) Calculate the density of the air as it leaves the nozzle.
What is the mass flow rate of airflow, with a Mach number of 0.230, Area of 10 in^2, Speed of sound of 200 ft/s and a pressure of 0.95 atm?
THERMODYNAMICS. Question I. 0.04 kg/s of an ideal gas (molecular weight 30, ratio of specific heats 1.5) flows through a duct with a cross sectional area of 10 cm?. The pressure and temperature are 100 kPa and 350 K. What is the velocity of this gas flow, in m/s?
The angle of the weak oblique shock wave = The angle of the strong oblique shock wave = Mach number downstream the weak oblique shock wave (M2) Pressure downstream the weak oblique shock wave Temperature downstream the weak oblique shock wave
61. For an airplane flies at two altitudes, find the temperature of air at second level, (µ1 = 31°, v2 = 750 m-s", the Mach no. ratio is 1.15). محمد طالب تركي
During actual processes of → expansion and compression of gases, the pressure and volume are usually be related to a process called polytropic, whose pressure can be expressed as P = CV-n where n is the polytropic exponent, and this can be equal to unity or different. a) If n = 1, show and explain the process that occurs and how the work of border? b) If n = 1, what process does the calculation of boundary work resemble, show and explain?
Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost.Figure Q1.a: Schematic of a Jet engine. (i) In analysing this nozzle using the 1st law of thermodynamics, the change in which type of energy is negligible?
Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost. Figure Q1.a: Schematic of a Jet engine.(ii) Determine the density and velocity of the air entering thenozzle.
Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost.Figure Q1.a: Schematic of a Jet engine.(iii) Calculate the density of the air as it leaves the nozzle.
1. Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost.Figure Q1.a: Schematic of a Jet engine.(v) Calculate the pressure of the air as it leaves the nozzle.
Air at 30 lbf/in2 absolute and 200F flows from a reservoir into a duct. The flow is steady, adiabatic, frictionless. The flow rate is 10lbm/s. What are the cross-sectional area, temperature, pressure, and Mach number at the point in the duct where the velocity is 1,400 ft/s?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS