TT IS Course EHide bloc A radial flow machine has an impeller with inlet diameter D1= 0.03m, outlet diameter D2-0.06m, inlet blade angle B1=40°, outlet blade angle B2=40°, and N=900 rpm. The angle of attack at the inlet is 90° Neglect the effects of slip conditions and losses, and assuming the radial flow components of the absolute velocity are the same at the inlet and the outlet. Calculate the specific work of the machine in J/kg Choose... Is this machine a pump or a turbine? Choose...

TT IS Course EHide bloc A radial flow machine has an impeller with inlet diameter D1= 0.03m, outlet diameter D2-0.06m, inlet blade angle B1=40°, outlet blade angle B2=40°, and N=900 rpm. The angle of attack at the inlet is 90° Neglect the effects of slip conditions and losses, and assuming the radial flow components of the absolute velocity are the same at the inlet and the outlet. Calculate the specific work of the machine in J/kg Choose... Is this machine a pump or a turbine? Choose...

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

This course EHide block A centrifugal pump with the following impeller dimensions is used to pump water. The pump is running at 1000 rpm. The ideal head rise through the pump is 190 ft. b2 Poz 72 by The parameters of the impeller are as follows: r2= 9in, b2=3in, B2= 31° Take g= 9.81 m/s23 32.2 ft/s2 pw = 998 kg/m3 = 1.94 Slug/ft. Determine the theoretical flow rate in gpm Choose.. Determine the theoretical Power shaft in (hP) Choose...
Q3/A pickup truck has a V6, 4-stroke, SI engine operating at (2800 r. p. m).the piston speed is (6 m/s) and the compression ratio is (re 11:1), and the brake mean effective pressure is (500 KN/m²) and mechanical efficiency (nm 0.60). if the bore and stroke relatives (S=0.92 B) calculate: - € 1-Stroke length (cm) 2-Total displacement of the engine 3-Brake power (Kw) 1 4-Indicated power (Kw) 5-Clearance volume of one cylinder.
asap
Q. A single stage impulse rotor has a blade ring diameter of 57.5 cm and rotates at a speed of 10,000 r.p.m. The nozzles are inclined at 20o to the direction of motion of the blades and the velocity of the issuing steam is 1,050 m/sec. Determine the inlet blade angle. Assume a friction coefficient of the blading equal to 0.85 and that the inlet and outlet angles are equal. Find also: (a) the power developed at the blades for a steam supply of 1,350 kg per hour (b) the diagram efficiency, and (c) the loss of kinetic energy due to blade friction
A piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping power with given flow conditions. Discuss the results. Design 1: Tank B 60 m 8 cm I 8 cm Pipe exit 40 m Sharp bend Pump Tank A Dia - 5 cm 18 cm Pipe inlet Sudden expansion 15 m
A 4x3-13 1750 rpm centrifugal pump equipped w/ an 11-inch diameter impeller requires 14.3bhp when delivering 300GPM at a head of 111ft. Predict the new capacity required when the diameter is reduced to 9 inches. Select the correct response: 235.5 gpm 230.45 gpm 240.45 gpm 245.45 gpm 220.32 gpm 225.45 gpm
Asap
Water at 20"C Bows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm respectively, and the width of the pump blades is 55 mm Part A Wan- μA Estimate the shaft power required to drive the pump at this operating condition Express your answer to three significant figures and include appropriate units. Value Blade Pump impeller The impeller rotates at 3600 rpm Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface. V is equal to 17 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s Submit Request Answer Units Outflow surface Inflow surface ? 160 บท 400 mun
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
The external and internal diameters of the impeller of a centrifugal pump are 0.3 m and 0.15 m respectively. The rotational speed of the pump is 1200 rpm and the vanes make an angle of 28° with the peripheral velocity direction at the outlet. The velocity of the flow through the impeller is constant at 1.7 m/s. Assuming the manometric efficiency of 82%, find the vane angle at the inlet (°). 18:19 /
Displacement (c): 0.2 in3/revShank diameter (d) = 0.625 in.Piston diameter (D) = 1.5 in.Rotation speed (n): 1725 RPMPressure (P): 600 PSIStroke (L) = 18in. a) Calculate the theoretical flow rate of the pump in in3/min and US GPM.Theoretical flow (Q) = Theoretical displacement (C) x Speed of revolution (n)Theoretical flow (Q) = 0.2 in3/rev x 1725 rpmTheoretical flow (Q) = 345 in3/min = 1.49 US GPM b) Calculate the cylinder output speed in in/s.Cylinder output speed (VS) = Piston side flow (Q) / Piston area (Ap)Cylinder output speed (VS) = (Displacement x Speed of revolution) / Piston area (Ap)Cylinder output speed (VS) = (0.2 in3/rev x 1725 RPM) / 1.77 in2Cylinder output speed (VS) = (0.2 in3/rev x 1725 RPM) / 1.77 in2Cylinder output speed (VS) = 196.02in/s = 196.02 / 60s = 3.20 in/s Questions: c) Knowing the output velocity (ram speed), calculate the rod side flow in GPM when the ram is extending. d) Calculate the piston exit time in seconds. e) Calculate the piston entry time in…
Q1): Impulse turbine diameter = 3.2m O1 = O2 Angular velocity = 25 rad/s Absolute velocities V1 = 140m/s and V2 = 110m/s Power developed by the wheel = 300kw Calculate: Jet 25mmd VI V: 1. the blade velocity. 2. the force exerted and 3. the angle O.