Machine Elements Problem. Solve what it asked. Thank you somuch in advance! Two flat belt pulleys have a center to center distance of 135 cm, and diameters of 72 cm and 36.6 cm, respectively. Compute thelength of belt if both pulleys will rotate (a) in the same direction, (b) in the opposite direction. What is the belt's angle ofcontact for a cross belt drive (in degrees)?(a)(b)(c)

Answer: (a) L = 442.9091 cm (b) L = 462.4291 cm. (c) Belt's angle of contact = 227.4344°.

Answered: Two flat belt pulleys have a center to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A belt drive operates with sheave sizes of 5.25 in and 13.95 in. If the center distance (C) is specified at 24 in, what is the theoretical belt length required? (A) 61.35 in (B) 70.25 in 78.93 in (C) (D) (E) 84.12 in 89.02 in
Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by a cross belt. The driving shaft is to turn 180 rpm while the driven shaft is to turn 50, 150, 250, and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find (a) the diameters of all the steps, (b) angle of contact for each pair of pulleys, and (c) belt length.
Two parallel shafts connected by a cross belt have the diameters of pulleys 40cm and 60cm respectively. The direction of rotation of the driven shaft is required to be reversed, by changing over to an open belt drive. State if the same belt can be used. If not, what is the remedy? Assume that the centre distance between the shaf is fixed at 6 metres.
A cross belt drive has a 6 in. pulley driving a 48 in. pulley. The distance between their centers is 96 in. Find the length of the belt needed. Please Show a clear and detailed solution (with illustration). Thank you!
In an open belt drive, two sheaves have diameters of 5 in. and 12 in. Determine the center distance of a drive utilizing a 72-in. belt. Also determine the angle of contact over the smaller sheave. Draw a 3d model of the mechanism.
Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if pulley diameters are 9 in. and 18 in., respectively.
For each mechanism, determine the mobility and the number and type of each kinematic pair: Q3 # of Turning Pairs: # of Sliding Pairs: # of Rolling Pairs: # of 2 Deg. of Freedom Pairs: No Slip. (a) (b) (c)
4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
8. A Hooke's joint connects two shafts whose axes intersect at 150°. The driving shaft rotates uni- formly at 120 r.p.m. The driven shaft operates against a steady torque of 150 N-m and carries a flywheel whose mass is 45 kg and radius of gyration 150 mm. Find the maximum torque which will be exerted by the driving shaft. [Ans. 187 N-m] mum
1. A pulley 580 mm in diameter transmits 60 kW at 650 1pm by means of belt. Determine the effective belt pull.2. Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if pulley diameters are 9 in and 18 m, respectively.
A motor with a torque of 37.26N/m and a speed of 120°/sec rotates a robotic arm that consists of two gears (one with a diameter of 4cm and 8 gear teeth and the other with a diameter of 10cm and 24 gear teeth). The arm is attached to the gears, and the arm must lift approximately 50 pounds of weight. The arm needs to lift about 1m distance. Find the following? 1) Find the amount of force required to lift the 50 pounds of weight 2) Find the power needed to lift 50 pounds. 3) Find the gear ratio for the gears to work properly. DC Motor Worn Gear Gear 50 Ibs
Find the center distance in (cm) of 4 direct contact rolling cylinders. Cylinders A-D have a speed ratio of 3:4:2:1. The center distance of cylinder A to cylinder C is 180 cm.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS