Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load Pi acting at the top is equal to 16 kN. The load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the rods are daB = 30 mm, taB = 12 mm, dac = 60 mm, and tec = 9 mm, respectively. Given that the lower part of the rod has the same compressive stress as the upper rod. Examine the required magnitude for load P2.

Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load Pi acting at the top is equal to 16 kN. The load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the rods are daB = 30 mm, taB = 12 mm, dac = 60 mm, and tec = 9 mm, respectively. Given that the lower part of the rod has the same compressive stress as the upper rod. Examine the required magnitude for load P2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.13P: A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines,...

See similar textbooks

Similar questions

A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
.15 A hitch-mounted bicycle rack is designed to carry up to four 30-lb bikes mounted on and strapped to two arms Gil (sec bike loads in the figure part a) The rack is attached to the vehicle at A and is assumed to be like a cant silkier beam A BCDGII (figure part b) The light of fixed segment AB is U = 10 lb. centered 9 in. from A (see figure part b) and the rest of the rack highs W2 = 40 lb. centered 19 in. from A. Segment ABCDG is a steel tube o(2 X 2 in. with a thickness I = 118 in. Segment BCDGII pivots about a bolt at B with a diameter d1 = 0.25 in. to allow access to the rear of the vehicle without removing the hitch rack. When in use, the rack is secured in an upright posit ion by a pin C(diameter o( pin d, = 5116 in.) (see phoo and figure part C). The of returning effect of the bikes on the rack is resisted by a force couple F h at BC. (a) Find the support reactions at A for the fully loaded rack. (b) Find forces in the bolt at B and the pin at C. (c) Find average shear stresses in both the bolt at Band the pin at C. (d) Find average bearing stresses o, in the bolt at B and the pin at C.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Three identical circular disks A, B, and Care welded to the ends of three identical solid circular bars (see figure). The bars lie in a common plane and the disks lie in planes perpendicular to the axes of the bars. The bars arc welded at their intersection D to form a rigid connection. Each bar has diameter d1= 0.5 in. and each disk has diameter d2= 3.0 in. Forces P1, P2, and P3act on disks A, B, and C, respectively, thus subjecting the bars to torsion. If P1= 28 lb, what is the maximum shear stress in any of the three bars?
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
Consider the sleeve made From two copper tubes joined by tin-lead solder over distance s. The sleeve has brass caps at both ends that are held in place by a steel bolt and washer with the nut turned just snug at the outset. Then, two "loadings" are applied: a = 1/2 turn applied to the nut; at the same time, the internal temperature is raised by ?T = 30°C. (a) Find the forces in the sleeve and boll, Psand PB, due to both the priestess in the bolt and the temperature increase. For copper, use EI= 120 GPa and ac= 17 × W+C; for steel, use E, = 200 GPa and a, = 12 × 10-6/°C. The pitch of the boll threads is p = 1.0 mm. Assume s = 26 mm and bolt diameter dB= 5 mm. (b) Find the required length of the solder joint, s, if shear stress in the sweated joint cannot exceed the allowable shear stress t ™ 18.5 MPa. (c) What is the final elongation of the entire assemblage due to both temperature change A T and the initial prestress in the bolt?
Q # 4: rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel. An aluminum rod is rigidly attached between a steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPа. CLO – 2 Steel Aluminum Bronze 2P P 4P 2.5 2.0 1.5
The figures below show a formed sheet-steel bracket. The total distributed load “W” on the bracket is 20 kN. It is secured to the support with two grade 5.8 bolts. The joint constant is C=0.183, and the bolts are preloaded to 70 percent of the proof load. The dimensions of the top flange are the same as the mounting flange.a) Find the external loads (P1 and P2) carried by upper and bottom bolts respectively if both resist the moment?b) Find the upper bolt diameter by ignoring direct shear load and determine/select a standard metric bolt size with a pitch for a design factor of 1,4.c) Is there any need to enlarge 5 mm dia. holes in the bracket?
b) Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load P; acting at the top is equal to 16 kN. The load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the rods are das = 30 mm, tas = 12 mm, dec = 60 mm, and tec = 9 mm, respectively. Given that the lower part of the rod has the same compressive stress as the upper rod. Examine the required magnitude for load Pz. P1 tAB -dAB |P2 B -dBC IBC Figure 5
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. In the given figure, the bent rod ABEF is supported by bearings at C and D and by wire AH. The portion AB of the rod is 250 mm long, and the load W is 540 N. Assume that the bearing at D does not exert any axial thrust. y A 250 mm 50 mm 30° 300 mm H 50 mm Determine the tension in wire AH. The tension in wire AH is F N. W D (You must provide an answer before moving on to the next part.) 250 mm