Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determinethe maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of thecross section.The following InteAv = 9KBv = 11Klocation of centroid = 3.56" above X-RefSheardiagramMomentdiagram1" x 10"steel plate1" x 8"steel plateX-referenceA6'8K12'24'12K6'Bof your work is accurate. YomentMmax = 66K'Vmax 11KMoment of Inertia = 218 inª

We know that Bending stress is given by σ = MI*y For Maximum bending stress we can write σmax =…

Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section.

Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Use the moment-area method to determine the slope and deflection at the free end C of the overhang…

A: A simply supported beam is given with a point load at mid of the support. There is an overhang on…

Q: 5) Find the support responses of the beam in the figure and draw the M, N, V diagrams. (P=19kN,…

A: The reactions can be shown as below

Q: A jet of water of 0.002 m² area moving with a velocity of 15 m/s strikes on a series of blades…

A: Are A=0.002 m2 Velocity V=15 m/s, Blades velocity u=6 m/s, It is needed to find the force exerted…

Q: Solid modeling may offer designs a more three-dimensional and organic look than lines alone.…

A: Solid modeling is a technique used in computer-aided design (CAD) and computer-aided manufacturing…

Q: Q₁/Water flows in the pipe shown in Fig. No. (1) from point No. (1) to point No.(2) at flow rate of…

Q: The roof of rigid gabled frames 5 meters on centers has a slope of 30 degrees. If the wind velocity…

Q: P5.16. For each beam, draw the shear and moment diagrams, label the maximum values of shear and…

Q: Use the Moment-Distribution method to draw the BMD and SFD for the frame below. Include sidesway in…

Q: A light house is just visible above the horizon from a ship. The height of light house is 150 m.…

A: A light house- Height of the light house h=150 m, To Find- The correct distance between the ship and…

Q: Question 6 A straight bar is fixed at edges A and B. Its elastic modulus is E and cross section is…

A: A straight bar fixed at edges A & B as shown- Elastic modulus = E, Cross-section area=A, Load…

Q: Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point…

Q: The fixed-end beam is subjected to a concentrated moment "M" at midspan as shown in Fig.1. Use the…

Q: A permeability pumping test was carried out in a confined aquifer with the piezometric level before…

A: Determine a. Depth of water at the farthest observation well (h2) b. Coefficient of Permeability…

Q: 1. A cylindrical tank 80 cm in diameter and 90 cm high is filled with a liquid. The tank and the…

Q: In a compound curve construction, if the length of the first curve is 268.3m and chainage at point…

A: Length of first curve L1=268.3 m, Chainage at point of curve = 623.3 m, It is needed to find the…

Q: Sample All round No. 1 2 pressure 1.0 2.0 Axial Pore stress Pressure 2.2 0.6 3.6 1.1 (i) Find total…

Q: Situation II: 4. Determine the minimum cross-section required for a rectangular beam from a shear…

Q: A California freeway has four lanes in each direction and carries a traffic volume of 4000 veh/h.…

A: Traffic volume- 4000 veh/hright shoulder lateral clearance- 5 ft Lane width= 11 ftfreeway length=1…

Q: moist soil has a void ratio of 0.65. The soil moisture content is 14% and its solids density or…

Q: 05 -09 falen of of -2x R10 R40 160 2 X R20 8 55- R10 40 65 R10 12

A: Given;- We have to draw the given plan in AutoCAD .

Q: Question-2: The cross section of the bar in the figure a) Calculate the stress(tension) values at…

A: Find: (a) Stress at points A, B, C (b) Stress distribution in the section

Q: This figure shows a cantilever beam that is subject to a point load and a moment. What is the…

A: Given data in question Load = P=60 KN Moment=M= 300 kNm Span member length=l= 10 m Elasticity…

Q: Home Work (Compound Truss) For the truss shown in figure, find the axial forces for the members…

A: The load of 5 KN is acting at Point C which is at a vertical distance of 7 m from A and B .

Q: Question The equilibrium cant required on a 5° curve on a BG track for the train speed of 60 kmph is…

A: Degree of curve D=5o For BG track, G=1.676 m Speed V=60 kmph, It is needed to find the equilibrium…

Q: Discuss the factors that affect the effectiveness of sound insulation

A: Sound absorbers are substances with a substantial capacity to absorb sound energy. When sound waves…

Q: TEXT:A beam ABC is supported by a uniformly distributed and a concentrated load as indicated in the…

A: A beam is given, we need to find out reactions and draw shear force and bending moment diagram

Q: Determine the magnitude of the hydrostatic force acting on gate AB, which has a width of

A: The hydrostatic law states that the pressure acting on point inside the fluid increases with…

Q: Determine the internal force in member CF.

Q: A train having 20 wagons weighing 18 tonnes each is to run at a speed of 50 kmph. The tractive…

Q: Two points A and B are in the HP. Point A is 30 mm in front of the VP, while B is behind the VP. The…

Q: 3. Two points A and B are in the HP. Point A is 30 mm in front of the VP, while B is behind the VP.…

Q: Draw N, V and M diagrams and determine Mmax- 3 m 5t 2 t/m 5 t/m

Q: A cantilever beam (member AC) is supported with a column (member CD). Force P is applied to Point B,…

Q: DO ONLY PART 3 Coordinates of Intersecting Points Length of Chord of the First Simple Curve is…

A: The Stationing of PC, PT, PC2, PCC, PT2, PC3, PRC, PT3 and End of Project: To find the stationing of…

Q: Re = 2* 106 e/d = 0.04 Find f?

A: We are given Re = 2 *106 ε/D = 0.04 Calculations shown in step below

Q: Uniform flow occasionally occurs in a 5-m-diameter circular concrete condui flow can vary. The…

A: Discharge or rate of flow (Q), is defined as the amount of fluid flowing per second through a pipe…

Q: Find the width (in m) of an elementary gravity dam whose height is 150 m. Specific gravity of dam…

A: Height H=150 m Specific gravity S=2.3 Seepage coefficient C=0.6 It is needed to find the width B…

Q: 1) Find the composite runoff coefficient, c, for a drainage basin having the following cover…

Q: Consider the cross-sectional area shown. Suppose that h= 60 mm. Determine the location y of the…

A: The centroid is the center of mass of the section of beam. It is considered as the center point of…

Q: Using Three Moment Equation. Draw the Shear and moment diagram. Please Show Complete Solution…

A: Moment distribution method: Solution: Fixed end moment: Span AB: MFAB=-wl212=-46×4212=-61.34…

Q: A confinéd aquifer is shown in Figure below. The aquifer has a hydraulic conductivity of 40 m/day…

A: Hydraulic conductivity (K) = 40 m/day Porosity (n) = 0.25 Average width of aquifer (B) = 4 km =…

Q: The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter.…

A: Member =58×10 Steel A36 → Fy=36 ksi → Fu=58 ksi Bolts are 78 in. diameter.

Q: During a daily routine observation, 12.4 litre of water was added to bring the water surface in the…

A: 12.4 litre of water, 4.2 mm of rainfall, Pan diameter = 127 cm.

Q: Show all possible water balance components (all express in equivalent depth of water) for a potted…

A: For a potted plant with holes at the bottom of the container placed in an open field, the water…

Q: Given a cantilever beam of length L=4.0meters. The left support “A” is fixed while the right end “B”…

A: The span length of the beam = 4 m The value of EI = 20000 kN-m2 The magnitude of the uniform load…

Q: Q1. Figure 1 shows the plan view of a reinforced concrete slab supported by three clay brick masonry…

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: A constant stress cantilever beam having a point load at the end is desired. The width b of the…

Q: 1.) For a given soil sample it has a sp.gr. of 2.74, moisture content of 16.6% and a moist unit…

Q: A tidal model has been made with horizontal scale ratio of 1: 7000 and vertical scale ratio of 1:…

A: Horizontal scale- LrH=1/7000 LrV=1/350 Natural period Tp=8 hour, It is needed to find the time…

Q: Figure 3 shows a two-span continuous beam with fixed supports at A and C and roller at B. Assume El…

A: MFBC and MFCB for the 15 kN force acting on the left side on the span BC. MFBC and MFCB for the 15…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine
the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the
cross section.
The following Inte
Av = 9K
Bv = 11K
location of centroid = 3.56" above X-Ref
Shear
diagram
Moment
diagram
1" x 10"
steel plate
1" x 8"
steel plate
X-reference
A
6'
8K
12'
24'
12K
6'
B
of your work is accurate. Yo
ment
Mmax = 66K'
Vmax 11K
Moment of Inertia = 218 inª

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Calculaion of Maximum bending stress

VIEW

Step 2: Calculation of Maximum shearing stress

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm
T'he pin is made of a material having a failure shear stress of Tail = 100 MPa. Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of F.S. = 2.5 against shear failure. %3D 80 kN
Q3) The beam system has a pin support at A, roller supports at D and F, and internal hinges at C. Find the deformations at C and E using the conjugate beam method. 10 kN A C D E F 100 kN-m k5 mt-5 m--5 m5 m-k10 m- = 100 x 10° mm*, and ICF Given: E = 200 GPa, IAC 50 x 10° mm“. %3D لقطة شاشة
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
The cantilevered W530 x 150 beam shown is subjected to a 7.5-kN force F applied by means of a welded plate at A. Determine the equivalent force-couple system at the centroid of the beam cross-section at the cantilever O. 0.58 m -5.3 m- 28 Answers: F = i+ i j) kN Mo = k kN-m
The plate shown is fastened to the fixed member to three 10-mm diameter rivets. Compute the value of the loads so that the average shearing stress in the rivet does not exceed 70 MPa. F= 74
Two overlapping plates are joined by a 0.75-in diameter pin. If the shear force on the pin is 0.5kips and the thickness of both plates is half of an inch, solve the bearing stress on each plate. O 1132ksi O 1333.333psi O 1333psi O 1131.768ksi l00oo
2. The structure is used to support a distributed load of = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3080 mm2.The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.