Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The assembly is pulled in tension by a force P. P = 100 kN. Find: a) The stress in each Steel Rod. b) The stress in the Aluminum Rod. Steel Rod Area = .5 m² Aluminum Rod Area = .5 m² P P Steel Rod Area = .5 m² Rigid Cover Plates

Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The assembly is pulled in tension by a force P. P = 100 kN. Find: a) The stress in each Steel Rod. b) The stress in the Aluminum Rod. Steel Rod Area = .5 m² Aluminum Rod Area = .5 m² P P Steel Rod Area = .5 m² Rigid Cover Plates

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.8P: A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure)...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A flat bar is 3/8 inches thick and has a centrally located drilled hole of diameter D. The bar is subjected to a 4,000 lb tensile load. Compute the maximum tensile stress adjacent to the hole. a) If the bar is 2 inches wide and D=0.25 inches b) If the bar is 2.5 inches wide and D=0.5 inches c) If the bar is 3 inches wide and D=1.00 inches Answers: a) = 15,969.5 psi (using k=2.62) b) = 13,066.7 psi (using k=2.45) c) = 12,000 psi (using k=2.25) I have no idea how to come up with these answers. Could you help me go through the process of solving for these answers step by step?
Jabbar Sku F Q2: A circular rod of 20 mm diameter and 100 mm length, is subjected to 2.5 KN tensile load if the diameter become 16 mm find 1. True stress. 2. The length of the rod after deformation.
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
Question Complebion Status: QUESTION 9 Consider the circular bent rod ith diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find all the components of stresses in section b-b. If you select wrong answers, you will have negative score in this question. 400 mm B 100 mm 300 mm al 200 mm 400 N 800 N O a Tyz O b. Txy Od.T Of Oy Chck Save and Submit to saue and submit. Click Save All Answers to save all answerS.
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
A bronze tire (thickness=12mm, width= 110 mm, internal diameter=800 mm) was heated and shrunk onto an 800.5 mm diameter bronze wheel. E = 83 GPa. 1. Find the Tensile stress in the tire. a. 51.8 MPa b. 121 MPa c. 107 MPa d. 125 MPa 2. Find the compressive force bet the tire and the wheel when pinched. a. 1.56 MPa b. 3.53 MPa c. 2.25 MPa d. 3.75 MPa 3. Find the minimum required wheel thickness when allowable stress is 124 MPa and the compressive stress is 1.5MPa. a. 4.0 mm b. 4.25 mm c. 3.52 mm d. 4.84 mm
Q1: A steel pipe column with outside diameter 0.5 in and its wall thickness 0,25 in. supports a load of 4.45 kN. The steel pipe rests on a square steel base plate, this base plate is resting on a concrete slab as illustrated in the attached figure. 1-Determine the bearing stress between the stcel pipe and the stecl plate. 2-If the bearing stress of the steel plate on the concrete slab must be limited to 90 nci what is the minimum allowable plate dimension (a)? 3-Determine the average shear stress in the steel plate, explain? Load Outside diameter - 6.5S in. Wall thickness - 0.25 in. Square steel- base plate Concrete slab
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod is 325 kN/mm?, calculate the minimum thickness of the rod. Give your answer in AIE