Use CONJUGATE BEAM METHOD to Determine the following: (a) slope at A (b) deflection at midspan on the beam shown The beam is a wide flange and has a modulus of elasticity of 200 GPa. Use the table provided for the dimensions of the section. |8 kN 48 kN/m B S130 X 15 -1m 1m Flange Web Thick- Thick- Depth Designationt A, mm? d, mm Width bf, mm Area ness ness tf, mm fw, mm S130 × 15 1890 127 76.2 8.28 5.44

Use CONJUGATE BEAM METHOD to Determine the following: (a) slope at A (b) deflection at midspan on the beam shown The beam is a wide flange and has a modulus of elasticity of 200 GPa. Use the table provided for the dimensions of the section. |8 kN 48 kN/m B S130 X 15 -1m 1m Flange Web Thick- Thick- Depth Designationt A, mm? d, mm Width bf, mm Area ness ness tf, mm fw, mm S130 × 15 1890 127 76.2 8.28 5.44

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

weight = 3758.0678Kg Leght is given the the FBD Inirta is = 39.2(10^6)mm^6 Gpa = 200 Please calculate the maximum deflection on the beam with you own sellected fomular that matches the digram
Use slope-deflection method to compute the bending moments of element ends for the following structures: 7) Use slope -defle ction Ast 4 4 12 t- 2006 Pa I= 100x 16mm" E = 200 GPa %3D I= 100× 106 mm4 For this question also compute the deflection at Point B.
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
C):-The rigid bar BDE is welded at point B to the rolled-steel beam AC. For the loading shown, determine (a) The slope at point 4. (b) The deflection at point B. Use E 200 OP 20 kN/m AT 24*2 s mid-1.5ml-1.5 m
Obtain an expression for the deflection curve of the simply supported beam of Fig. 8-7 subject to the uniformly distributed load w. W mmmmm Fig. 8-7 Determine the maximum deflection of above beam if E=100GPa ● W=200N/m L=4m Rectangular beam section 2cmx8cm (W x D) In addition, you are asked to, W ● Evaluate the types of connection that will be needed to provide the simply supported design ● Discuss the relationship between bending shear, and deflection. • Evaluate steel and reinforced concrete and their structural efficiency in managing bending shear, and deflection. Answer All Questions.
JC = For the beam and loading shown, determine (a) the deflection at C, PL 0 A P Bt² 2 EI (b) the slope at end 4. PL ↑P -L/3L/3L13 EI D
What is the deflection at the hinge for the beam shown below? А C I В I L/2- - L/2
Determine the design moment capacity of the beam with given properties below. bf = 550mm bw = 350mm tf = 110mm d = 370mm %3D d' = 100mm fc' %3D 34.5 MРа fy = 400 MPa As = 6 - 28mm bars %3D USE NSCP 2015, Mu = kN-m %3D
ht nces Required Information Portion BC of the rod ABC are made of an aluminum for which E= 70 GPa and portion AB is made of steel for which E= 200 GPa. Given: P = 8 kN, a = 0.9 m, b=1 m and the diameter of rod AB is c = 38 mm, (a) Determine the value of Q so that the deflection at A is zero (b) The corresponding deflection of point B 60-mm diameter Assume Q Is In (KN). Using the FBD/equilibriums equations of ABC and/or cut section between A&B and/or cut section between B&C, (1) The Internal axial force between A&B can be written as PAB= (KN) (T) -Q) (KN) (T) (11) The Internal axial force between B&C can be written as PBC=(
回の at D ana Pa at all 400 MPa of 3.0 is 4.0 m рe aplied nd the pin Q9. Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Knowing that the magnitude of P is 4 kN, determiñe (a) the value of Q so that the deflection at A is zero, (b) the corresponding deflection of B. 20-mm diameter 0.4 m 0.5 m 60-mm diameter 2.
Required information Consider the loading condition shown. Assume that the flexural rigidity El of the beam is constant. 21 W B -L/2L/2L/2- The deflection at point B is. 0013 W Using singularity functions, determine the deflection at point B and point D. (Round the final answers to four decimal places.) The deflection at point Dis. -0.0163 wwwwwwwwww………… 1 D x Deflection point at D is wrong
Virtual Work for Beams and Frames #2 Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(10°) mmª. P = Last 2 digits of ID number a = 5th digit of ID number (max value = 3) P Use %3D 4 kN ID # = 18-2363-391 P = 91 a = 6, but use 3 (max) e.g., A C |D B- a - 3 m -3 m