Answered: Use the impulse invariance method to…

Use the impulse invariance method to design a low-pass digital Butterworth filter to meet the following specifications: 0.9 < |H(el")| < 1 |H(el")|s 0.2 l이 s 0.2π 0.3m < lw| S Tn

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Given of x[n] = {x[0] = 2,0, 2, 1}. Interpolate x[n] by a factor of 2 using the low-pass filter h[n]…

A: Given: x[n]={x[0]=2, 0, 2, 1} and the low pass filter h[n]={1/4, h[0]=1/2, 1/4} we have to…

Q: 0.4 03:) For a system having the Transfer function G(s) Find the magnitude and phase of the s+ 0.2…

A: The given input is, θit=0.1sin6t+20=0.1∠20° The given transfer function is, Gs=0.4s+0.2=Hs For…

Q: 3) Impulse response of an FIR and LTI system with linear phase is given as: h(n)={1, -1/2, 2, -1/2,…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: b) Consider the 1st order analog low-pass filter: G(s) = which we want (s+2) ' to implant as a…

A: b) Analog T.F.Gs=2s+2sampling period of T=0.1 sec

Q: Obtain an analog Chebyshev filter transfer function that satisfies the constraints in S IH(jN)| < 1;…

Q: The signal x(t) = 1+3 cos -t+sin 3 V is passed through an RC low-pass filter shown below, 3 where…

A: According to the question we need to calculate the value of , (a)input spectral density (b) output…

Q: Find the out put spectrum of an LTI system if input x(n) = 2/3, - 1sn<1 %3D = 0, else And impulse…

A: To find the output spectrum of discrete signals Find output in z-domain using Y(z)=X(z) H(z) Put…

Q: Find the out put spectrum of an LTI system if input x(n) = 2/3, –1<n<1 = 0, else And impulse…

Q: The relationship between input and output for an LTI system is defined by the following equation of…

Q: A low-pass filter with a x(t) signal wc= 1000 cutoff frequency is obtained from the output. In which…

A: For recovery, the condition should be ωm<ωc<ωs-ωmωs≥2ωm so the condition must be ωs-ωm≥ωc

Q: The Transfer function H(z) of a digital filter is given by H(z) Q1. = 1-3z-1 1+3z 1+2z-2 Realize…

A: Given: H(z)=1-3z-11+3z-1+2z-2

Q: Consider the LTI filter with impulse response [sin(an/8)] h[n] = 8 · cos(In/2) The input to the…

A: Given the LTI filter with impulse response: h(n)=8sinπn8πn2.cosπn2 The input to the filter is given…

Q: A voice morphing system internally performs the filtering operation using the IIR filter described…

A: As per bartleby expert policy, only first subpart is to be answered. if you want answer for another…

Q: You are asked to design an RC- low pass filter circuit with a cutoff frequency wC 100 rad/sec. If…

Q: (b) Compute the bandwidth of a band-pass filter whose critical frequencies are 170 kHz and 258.4…

Q: yMn) - ayln - 1]+(1-a)x[n]. where 0< a<l is a real constant. Determine the system function of the…

Q: Suppose that an input of x(t) is applied to a causal LTI system whose magnitude response and phase…

A: a) The input power is calculated as shown below:…

Q: Q1: In Matched filter, given the below input signal x(t), N, 10 Joul, find SNR. 3 2 1 x(t) 2 8 9 10

Q: given by S.(f) 1 ,-10 < ƒ < 10, S.f) = 10II (5000 f П S„(f) 5000 The input signal is passed through…

Q: A high pass filter is found to attenuate a 1kHz signal by 20dB. What is the critical frequency? [dB…

A: Given, An High pass filter has Attenuation (A)= 20dB at frequency (f) = 1kHz

Q: Consider the following LTI system S, that is characterized by its input -output relationship, where…

A: Linear time invariant (LTI) systems are characterized by its input-output relation ship called…

Q: 2. Suppose that an input of x(1) is applied to a causal LTI system whose magnitude response and…

A: From the sinusoidal steady state response

Q: Given the FIR filter with the following difference equation, y[n] = x[n] + 4.2 x[n – 1] + 5.5 x[n –…

Q: Q4 Given x[n] = {x[0] = 2, 4, 2, 1}. Decimate x[n] by a factor of 2 using the low-pass filter h[n]…

Q: Given an LTI system with the transfer function H(jΩ)= e-jΩ (2+2cosΩ), the input signal…

Q: (1, t20 -400 rt Question 2 A signal x(t) = e u(t), where u(t) = (0, 1B [0, |f|>B Find the value of B…

Q: The transfer function of a third-order Butterworth low-pass filter having dc gain = 1 and a cutoff…

Q: d) kHz. Plot magnitude frequency spectrum of the sampler output if the filter input is given by i)…

A: First we will find the output of LPF , then we will find out spectrum for sampled signal .

Q: 10 k2 10 k2 Vo 2.2 k2 V1 0.05 µF FIG. 11.57

A: The solution is given below

Q: 3. Using straight line approximation, draw the Bode logarithmic magnitude response diagram of a…

A: A transfer function of a system is given. We need to draw the bode logarithmic magnitude response…

Q: Q.1. Design a digital Butterworth low-pass filter which satisfies the following constraints 0.8 s…

Q: A digital filter with a 3 dB bandwidth of 0.25TT is to be designed from the analog filter whos…

A: Given, H(s)=Ωcs+Ωc and, ωc=0.25π

Q: s+0.1 For the system transfer function, H(s) , determine: S+5 i. The frequency response of a system.…

Q: *2. Consider a continuous time signal, x(t) = E}=1 A¡ cos(2nF¡t + 0¡), consisting of a sum of…

Q: Consider the LTI filter with impulse response [sin(an/8)] h[n] = 8 • cos(In/2) πη The input to the…

Q: A signal, x(t) is described by : X(t) = rect(1000t)*S0.002(t) X(t) is the input of an ideal lowpass…

Q: Determine if any of the following transfer functions represent a realizable filter: 1 H(s) = (s²…

A: According to the question, for the given transfer function as shown below We need to determine if…

Q: The signal x(t) isa ideally sampled at f = 1kHz rate. The sampled signal is then bandlimited to 500…

Q: A digital audio filter has lowpass characteristics with specifications: 25dB; T = 1. 0.2n; w, =…

A: Given: A digital audio filter has lowpass characteristics with specifications: To find: Determine…

Q: 5.38. An ideal lowpass digital filter has the frequency function H(N) given by 1, 0 s |2| < H(0) 0,…

Q: 1. (a) The impulse train x(t) = E=-o 8(t – mT) is applied to an ideal lowpass filter having a cutoff…

Q: 3 a. The transfer function of analog filter is Ha(s) = (s+2)(s+3) Design a digital IR filter using…

A: Given analog filter,Ha(s)=3(s+2)(s+3) --equation1sampling frequency, fs=10…

Q: Design a digital Butterworth low-pass filter which satisfies the following constraint 0.7 <|H(e")<1…

Q: 5.25 Suppose H(z) is an allpass filter with input x(k) and output y(k) whose magnitude response…

A: Suppose H(z) is an all-pass filter with input x(k) and output y(k) whose magnitude response…

Q: 4 Find the transfer function of digital filter shown K(n) x(n). (E) (2) y(n) 2 Z ½/₂ -1/4

A: We need to find out the transfer function for given system .

Q: given z(t)=sin(5 t), and time period = -2<t<2, use Matlab to find magnitude and phase plot (sampling…

A: Below is the matlab code and the plots at sampling frequency 200Hz Please find the attachments

Q: 5.25 Suppose H(z) is an allpass filter with input x(k) and output y(k) whose magnitude response…

A: If H(z) is an All-pass filter, and an All-pass filter passes all the signal frequencies with equal…

Q: 3. A biological signal, x-(t), which has a bandwidth of 2kHz has been sampled with using Fs = 8kHz…

A: Part (a): Sampling Process: From the given diagram, the Fourier transform of the signal can be…

Q: Determine the attenuation of a fifth order Chebyshev filter at w=2w, provided by a Butterworth…

A: Chebyshev filter This kind of filter use for distinct frequencies of one to another band. Their…

Question

Use the impulse invariance method to design a low-pass digital Butterworth filter to meet the
following specifications:
0.9 < |H(e/")| < 1
|H(e/< 0.2
l이 s 0.2π
0.3m < lw| S n

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Trending now

This is a popular solution!

Step by step

Solved in 8 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Infinite Impulse Response (IIR) and Finite Impulse Response (FIR) Filter

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that allows the spectral components between the sequences fa=12kHz and fb=16kHz to pass. If you are using a 32 tap FIR filter. A) Center the response of the bandpass filter at zero frequency and plot the frequency response of the resulting lowpass filter.
The following transfer functions represent digital filter meeting identical amplitude-frequency response specifications: H(z)= 5+0.6z-1/1+2.5z-1+3z-1+4z-2 For filter,a) State if it is an FIR or IIR filter.b) Represent the filtering operation in a block diagram form and write down the difference equation.c) Determine and comment on the computational and storage requirements.
b) Canonic realisation of a digital filter is shown below. Determine the transfer function of the filter. Determine and comment on the system's stability. x(n) y(n) z1 0.5 1 -0.5 -0.4
Exercise. There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that allows the spectral components between the sequences fa=12kHz and fb=16kHz to pass. If you are using a 32 tap FIR filter. 1.-Draw the frequency response for the bandpass filter
A student is doing a measurement using a sensor at 400HZ. However, there is noise present at 0.5MHZ. Help the student to improve the measured data by: (i) (ii) Designing a low-pass filter that can attenuate the noise by 97%. What is the effect of the filter to the data signal?
Design and sketch the block diagram of the receiver that will recover signals, m, (t) and m(t) from the modulated signal c(t). Specify the type and the cutoff frequency for every filter you use in your design, give the specifications for any other component you might use. Write all design parametrs on the receiver.
Given certain specifications to design a Butterworth filter using Bilinear transformation, if the obtained values of N and Q, where as follows: N = 7.2 and Q. = 0.72 %3D Which of the following angles is not an angle (in degrees) of one of the filter's stable poles? O 78.75 O 168.75 O 213.75 O 258.75 O None of the above
) With respect to an analog Butterworth filter, explain the following terms a. filter response b. filter design parameters ii) An analog Butterworth filter has 2dB passband attenuation at a frequency qf 10 rad/sec and 30DB stopband attenuation at 30 rad/sec. Compute the order of the system.
If a lowpass filter with 40 dB.decade roll-off rate has resistror R = 3 kohms and capacitor C = 0.1uF. therefore a 600 Hz frequency belongs to * transition region None of the choices critical frequency itself All of the choices O passband O stopband Created by SEASOFT LTD.
To recover the original signal, the low-pass filter with cutoff frequency should be Select one: a. We = @g-WM O. b. We = Ws C. WM We > Wg=@M as page Next page al Assessment (20%) EECE-3 Jump to... +30-6:30 pm) MacBook Air 000 D00 F4 F7 F8 F9 F5 F6 &
a x[n] Σ D y[n] D Consider a DT system described by the block diagram shown in the figure. For a = 0.90, select the value of the magnitude of the frequency response at w = 0 and DT filter type from the choices below. 0.474; highpass filter 0.474; lowpass filter 0.669; highpass filter 0.669; lowpass filter O 0.474; bandpass filter 0.669; bandpass filter
There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that lets the spectral components pass between the fa=12kHz and fb=16kHz sequences. If you are using a 32-tap FIR filter. What is the value of the central frequency, f0, in Hz of the band that passes the filter? And what is the outline of the frequency response for the filter passes bands?