Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. Following are the sequence of operations 1. The operation is to be started using a push button (use the label START PB). Include a stop push button (use the label STOP PB) to stop the process at any time. (Use Memory ON circuit) 2. An acknowledgement signal (S1- Limit switch) is required when the piston is fully extended, to ensure that the work piece has been tipped onto the belt. 3. The extension should be slower than the retraction (use flow control valve) 4. The return stroke should be automatic. a. Design the Electro- Hydraulic Circuit with proper labeling. Include the components required b. Draw the Displacement -step diagram & Displacement -time diagram (include Cylinder, START PB, STOP PB, DCV and S1)

Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. Following are the sequence of operations 1. The operation is to be started using a push button (use the label START PB). Include a stop push button (use the label STOP PB) to stop the process at any time. (Use Memory ON circuit) 2. An acknowledgement signal (S1- Limit switch) is required when the piston is fully extended, to ensure that the work piece has been tipped onto the belt. 3. The extension should be slower than the retraction (use flow control valve) 4. The return stroke should be automatic. a. Design the Electro- Hydraulic Circuit with proper labeling. Include the components required b. Draw the Displacement -step diagram & Displacement -time diagram (include Cylinder, START PB, STOP PB, DCV and S1)

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.5: Introduction To Cnc Milling

Problem 7RQ: A programmable indexing fixture creates a fourth axis called a ________ __________ that is similar...

See similar textbooks

Similar questions

An emergency stop system is to be designed for a certain automatic production machine. A single “start” button is used to turn on the power to the machine at the beginning of the day. In addition, there are two “stop” buttons located at two locations on the machine, either of which can be pressed to immediately turn off power to the machine. Let X1 = start button (normally open), X2 = stop button 1 (normally closed), X3 = stop button 2 (normally closed), and Y = power-to-machine. (a) Construct the truth table for this system. (b) Write the Boolean logic expression for the system. (c) Construct the ladder logic diagram for the system
1. In the drilling process shown in Figure 1, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation is as follows: activate the direction control valve to start the process, Cylinder A and Cylinder B clamps the workpiece and then activate the second directional control valve to drill cylinder lowers the drill and raises afterwards. Once the drill is raised, cylinder A and cylinder B retracts. sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B A+ B+ sensors Figure 1: Drilling Process а) Design the Hydraulic Circuit with proper labeling. Include the allocation list and the components required b) Draw the functional diagram/step diagram
The reversing motor,which is controlled by two power relays,can be rotated in both directions as shown in the figure beiow.When the motor is mechanically combined with a lead screw,the rotary motion is converted to a linear one,such as the one moving lef tor right on the worktable in the layout.The desired direction of rotation is selected via the two STAFIT buttons,respectively.The limit switches LS1 and LS2,located at the two extreme motion limits,ensure 1-rqtf we forget to stop the movement of the worktable,then it will stop automatically, and the mechanism of the layout will not be destroyed.Draw the circuit of automation.
Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as; 1. Crank-rocker mechanism; 2. Drag link mechanism; 3. Double rocker mechanism; 4. Crossover-position or charge-point mechanism; 5 Triple rocker mechanism (non-grashof). Use technical Pen for the following: 0.2(light -for linkages and hand writing), 0.4(medium - for joints), 0.6(heavy - for fixed link or frames) use 2-4-4 template, all caps, italicized.
Name Section 5-2: Line Diagrams-Signals, Decisions, and Actions In the following application, a temperature switch controls a heating contactor and a flow switch is used to ensure there is enough air flow. If there is not enough air flow, an alarm is sounded. Complete the required information. 1. List all the signal devices in the circuit. 2. List all the action devices in the circuit. 3. List the decision part of the circuit that automatically sounds the alarm if there is a problem. 4. When the heating element is on during normal operation, is the flow switch open or closed? CIRCULATING 2 L1 FAN TEMPERATURE SWITCH TR HEATING ELEMENTS FLOW SWITCH -HOT AIR PADDLE AIR FILTER NORMALLY CLOSED FLOW SWITCH 65 ALARM (SOUNDS IF NO FLOW FOR 15 SECONDS OR MORE) Date HEATING CONTACTOR TR ON-DELAY TIMER SUPPLY AIR COLD AIR (3) TIME SET= 15 SEC © 2014 American Technical Publishers, Inc. All rights reserved
Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing the start pushbutton makes 5 cycles. After making 5 cycles lamp is energized for 3 secs. Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs. Then retract. Cylinder A retract.
Use time delay A push button is to control the forward stroke after the piston rod has reached the forward end position the components are to be pressed together for 20 seconds then the piston rod is to return automatically to the initial position Additional condition The return stroke must occur even if the start push button is still depressed A new start signl may only become effective after the initial position has been reached and after the push button has been released
Problem Description Components are to be continuously stamped with a stamping device. After the start button is pressed, the die is pushed down and the component is stamped. The die is to return to initial position after five (5) seconds. The sequence stops automatically after five (5) cycles. Start button should reset the counter. Inductive sensors S1 and S2 are used to check the fully retracted and extended positions of the cylinder. Draw the following: Pneumatic circuit diagram Electrical circuit diagram
Please the following question in attach file
In the drilling process shown in Figure 2, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation is as follows: Start push button is used to start the process, Cylinder A and Cylinder B clamps the workpiece simultaneously and then drill cylinder lowers the drill and raises afterwards. Once the drill is raised, cylinder A and cylinder B retracts simultaneously. sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B B+ sensors B Figure 2: Drilling Process For the above given drilling process: a) Provide the allocation List for the given application. b) Draw the grafcet and extract the grafcet equation. Obtain the ladder program from the grafcet equations.
It is desired to operate the pneumatic cylinder below which has to pistons A and B to stamp the die D. The piston A s returned in its back stroke by a spring, and has quick return .It is advised to use solenoid and pilot valves DCV . ( best design is to use two DCV valves ) 1- Make a complete circuit layout to operate the device above, using the appropriate symbols.2-Describe in details how your system works ( typed ) 3- Names the components of your system. 4- Any pneumatic working design will be considered as correct.
What is the difference between a lever and a crank?. note: answer the question in 8-10 sentence only