V Thing Pipe area = 0.10 m2 Water flows at a rate of 1.6 m /s from a large tank and passes through a "thing" which is either a turbine or a pump, as shown in the figure. The water elevation is z = 30m and head loss is known to be 0.9v2/2g. Determine 1) is the "thing" a pump or a turbine? 2) what is the head [m] added or removed by the thing?

V Thing Pipe area = 0.10 m2 Water flows at a rate of 1.6 m /s from a large tank and passes through a "thing" which is either a turbine or a pump, as shown in the figure. The water elevation is z = 30m and head loss is known to be 0.9v2/2g. Determine 1) is the "thing" a pump or a turbine? 2) what is the head [m] added or removed by the thing?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2- Water density =1000 kg/m and viscosity is 0.001 Ns/m², is pumped between two reservoirs at 0.2m/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Z1 level in meter. Screwed Z2= 50 m regular 90° elbow Sharp exit Z;= ID m Sharp entrance Half-open gate valve `bend radius Pump Open globe valve 8 cm diameter
b) What is the volume flow rate through the pipe, in m³/s? Yanıtınız
(95 7 A U U O b vol1:EA محو التحدید Q6: Water enters a horizontal pipe with a rectangular cross section at a speed of 1 m/s. The width of the pipe remains constant but the height decreases. Twenty meters from the entrance, the height is half of what it is at the entrance. If the water pressure at the entrance is 3000 Pa. what is the pressure 20 m ?downstream 1.5 Pa 15 Pa 150 Pa 0.15 Pa 1500 Pa Note: Solve each question in a separate sheet of paper with your name. Take pictures and upload them with your form. Then submit your å lla K la work
Directions: In any clean sheet of paper, write your name, solve the problem and show your solution. Box your final answer. Take a picture of it and upload it here (image/pdf). 1) Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, P1=1300 kgm/m3. At exit: A2-10 m2, 02=0.00125 m /kg, Ü2=3 m/min. Determine the following: a) m, in kg/min b) Ủz in m/min
A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters), (provide your answer with four decimal points) P Type here to search O 10°C Sunny AQA ENG 0029 16/02/2022 DELL priSc FS F6 5 E R J K L %23 F E Aock C V sage page VO at gr ctri
A pump delivers water from a tank (A)X water surface elevation-110m) to tank B (water surface elevation= 170m). The suction pipe is 45m long and 35cm in diameter the delivered pipe is 950m long 25cm in diameter. Loss head due to friction hf1 = 5m and h2 3m If the piping are from pipe(1)= steel sheet metal pipe(2)= stainless – steel Calculate the following i) ii) The discharge in the pipeline The power delivered by the pump.
As shown in the figure below, a cylindrical tank with a hole in the bottom and an air vent in the top is being filled with water. Given the following: Dtank = 4 ft hill = 8 ft NOG height of water in tank when tank is filled Qin = 10 gal/min %3D NOT UPL TO CHE diameter of hole Find: volumetric flowrate into tank EGG EXAM into the tank in slugs/second OT UPS XAM O NOT U EXAM (c) The rate at which the water level in the tank is mass flowrate (in slugs/second) of the water (b) The mass flowrate (in slugs/second) out of the tank UPLOAD TO CHE NOT UPLOAD when the water level reaches the fill height DO NOT UPL rising (in inches/minute) when the water level NOT UPL PLOAD TO CHEGG NOT UPLOAD TO CHEGG EXAM TO CHEGG EXAM OD TO CHEGG UP reaches the filled height то снE LOAD vent Dtank DO DO DO NOT UPLOADTO EXAM EX DO 0 DONOT UPLOA T Dhole G EXAM TO CNGO UPLOA hole mdotout
Water flows through a venturi as shown in the figure at a flow rate of Q-57.1 L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm and d = 2.5 cm) respectively. The height of water column in the manometers L, and L, are 65 and 53 cm respectively. What is the experimental dynamic head at the throat-{section2) (in m)? LI 3) D D 2)
Gentlemen, please check and help me with question #3 Tank filled with water and orifice diameter of 3 cm in the bottom. Height between centre of orifice and water level 3 m. Coefficient of discharge - 0.64, coefficient of velocity- 0.97. Find: 1. Actual jet velocity? This one I know how to do. V(actual) = square root from 2gH 2. Jet diameter? This one I know as well. Coefficient of contraction= coefficient of discharge/ coefficient of velocity Diam of jet we will find from formula: Coefficient of contraction = (diameter of jet/diameter of orifice)^2 3. How long will it take for jet to be established?
Water flows through the elbow. It exits to the atmosphere at section 2. The inlet and exit pipe diameters are D,=10 cm and D2=3 cm, respectively. At a weight flow rate of 169,9 N/s. The elevation difference between the inlet and outlet sections is 25 cm. Neglecting the weight of water and elbow, estimate the force [N] on the flange bolts at section 1. (NOTE: pwater-998 kg/m3) 25 cm 40°
Q3/ Water is flowing upwards in an inclined homogeneous pipe from point No. (1) to point No. (2). The following data is available:- 1- Length of pipe, L= 1400 (m). 2- Diameter of pipe, d= 0.25 (m). 3- Elevation of point No. (1) is 15 (m) above the Reference line and elevation of point No. (2) is 30 (m) above the Reference line. 4- Piezometric head at point No. (1), hi= 61.16 ( m of water height). 5- Piezometric head at point No. (2), h2= 20.39 (m of water height). 6- Friction coefficient f=0.02 and hL=zero Find: 1- Head loss of water flow in the pipe from point No.(1) to point No.(2) due to friction hf. 2- Water flow rate Q and flow velocity v in the pipe. Draw the H.G.L. of water flow in the pipe from point No. (1) to point No. (2).
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.