velocity of the collar is 0.1 m/s. The spring attached to the collar has an undeflected length of 10 cm and a constant of 3 N/m. Calculate the distance x of position 2, where the collar will come to a stop. A 2-kg collar slides without friction along a horizontal rod as shown. At the position 1, the 20 cm- Vi= 0.1 m/s ww x = ? ww 2.

velocity of the collar is 0.1 m/s. The spring attached to the collar has an undeflected length of 10 cm and a constant of 3 N/m. Calculate the distance x of position 2, where the collar will come to a stop. A 2-kg collar slides without friction along a horizontal rod as shown. At the position 1, the 20 cm- Vi= 0.1 m/s ww x = ? ww 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D shown in the figure below is 300 mm² and a modulus of elasticity is 105 GPa. A single force P-90 KN acts on the Kafcs system from point A as shown in the figure. Determine the vertical displacement at point A using the work-energy method. 2 m B P 1.5m
Determine the change in length, breadthand long,semm thickness f a steel bar which is 4 m wide and 20 mm thick and is subjected to axial pull of KN in the divechion of leng th. E = 2xlo/m, = 0.3
Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member BC. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
1. A 6 kg slider is released from rest at Point A and slides with negligible friction in a vertical plane along the circular rodshown below. The attached springhas a stiffnessof 520 N/m and an unstretchedlength of 0.6 m.a. Determine the change in potential energy when the slider is at B in joules. b.Determine the change in elastic potential energy when the slider is at B in joules c. Determine the velocity of the slider at B in meters per second.
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
D (5000 mm?) (4000 mm (5000 mm?) 3 m (4000 mn) (5000 mm) B (5000 mm?) A 100 kN 2 panels at 4 m 8 m E = 200 GPa Analyze the truss shown using MCD. Determine the force in member AE. For reactions that is downward and going to the left, input your answers as negative. * („uu 000) /4000 mm)
Determine shear stress at support on cantilever beam as shown in figure. b = 300mm. 500mm mm 120kN/m -2.7m- 200mm
Situation 46 Considering the frame shown in figure below, E = 200 GPa, 1 = 2x 10⁹ mm4. The frame is fixed supported at point A and roller support at point C. a. Determine the vertical reaction at support A. b. Determine the horizontal reaction at support A. 20 KN 3m 3 m B A 8 kN/m 9m C
A propped cantilever beam XY, with an internal hinge at the middle, is carrying a uniformly distributed load of 10 kN/m, as shown in the figure. The vertical reaction at support X (in kN, in integer) is 2 m 10 kN/m Enter Your Answer... I 2 m Y Check
A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
Question [3] The beam AB is loaded as shown in the figure below. You are required to: b) Draw the FBD. Calculate moment at point O. Calculate the horizontal and vertical reactions at point O. O 0.2 m -1.5 m 30° 400 N 2 m 250 N 300 N.m 1.5 m-
Question 1 Determine the reaction at B in kips on the beam shown. Assume A is a pin and the support at B is a roller (smooth surface). || A 500 lb/ft 7 ft B 4 ft