Water at 15°C is pumped from a reservior at a rate of 0.1131 m3/s where the local atmospheric pressure is 94.6 kPa. The total head loss in the suction pipe is 1 m. From the manufacturer data, the NPSHrequired at this operating point is 7.8. Determine the maximum height hs (meters) before cavitation can occur. Round off your answer to 3 decimal places.

Water at 15°C is pumped from a reservior at a rate of 0.1131 m3/s where the local atmospheric pressure is 94.6 kPa. The total head loss in the suction pipe is 1 m. From the manufacturer data, the NPSHrequired at this operating point is 7.8. Determine the maximum height hs (meters) before cavitation can occur. Round off your answer to 3 decimal places.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Similar questions

value of reynold number for fluid flow in pipe and flow is laminar?
Sat wr oted 120.3°c through steel Yepor Flows Pipe (上 = 25 3K) steel hos diometer The Pipe inside 52 5 33i outside dione ter 58.5 ond length 30m The Surf a ce of in suloti^g Pipe is cooted w.th moteria( which hos of thick ness 25 mm(k=0,25 wimk k 0, 25 w/mk) The ambien + temper ture is 27°C Find the amount of heat los8 and of woter Con den sates in = 2705 6 ヒ1kgk Pipe Hvopor Saturoted water =505.4 Wikgk SHOT ON MI6 MI DUAL CAMERA
BA4s6nknAPkVXhnUEg rmResponse Good Luck... PROBLEM 1 Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube Given is a thin-walled tube with the following data: Wall thickness-2mm ABC is a sector with a radius of 50 mm AOD & COD is a triangle C. Shear flow d. Shear stress e. Angle of twist Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium A 90 B D 3R PROBLEM 2 Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow d. Shear stress Given is a thin-walled tube with the following data: Wall thickness- 3mm Torque is 900 N.m Length of the thin walled tube is 1.2 m. Use G=24 GPa for aluminium e. Angle of twist Ps Xd étv W
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol What is the a.) value of G in kg/s.m2? b.)value of friction factor? 3 significant figures c.)the % of pressure drop? d.)the outlet pressure? e.) compressible or not?
long. The inlet water temperature is 10 C, and the tube wall temperature is 15 C water temperature. k 0.585, Pr= 9.4, u= 1.31x10*,p= 992kg/m, CP= 4195 j/kg. higher than the water temperature all along the length of the tube. What is the exit %3D Q5//answer one of the following branches e jall al je yal A) cast iron pipe (k=75w/m. °C) air flows inside this pipe at 300°C the inner diameter is 0.06 m, the outer diameter 7cm,it is covered with insulation type glass wool with thick 4cm. with k= 0.055w/m.°C .the ambient temperature 6 °C by free V3. convection with heat transfer coefficient (20w/m2. °C) the heat transfer inside the pipe is 65 w/m?. °C. length of tube (L-2) determine 1-the heat lost from the hot air 2-the temperature drop across the pipe shell 3-the temperature drop across the insulation. 344 14. 1256 and B) Fill the blanks: of the 1. The thermal resistance of a medium depends on medium. 2 All law. pes of convection are governed by 10000, the flow is
What is the critical velocity for an oil of viscocity 4.413x10-6m2/s flowing through 152.4mm diameter pipe?
Plot curves on a single plot that display the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure as 0 to ~1 MPa). Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
C- A fluid flowing in a tube with long (L) and diameter (D) at mean flowing velocity of (Vm). show that the friction coefficient can be given by: (C₁= 16/Re)
EX in Asteel of speçific weight cy lin der (1"diametar andiz" Long) (8) =490 1b fI Ft3 fall be Cause of its own weight, at q uniform slig htly 9. rate of on5 HIs in side a tube of larger diameter.A Castor- oil film M = 6x lo -3 16 between t-s Constant thihness and the tube between of %3D is the cylinder Determine the cleamanCe (y) in ft the Cylinder and the tube-
slepe of Iom in 100 and and topes 300m long has a pipe from Im diamete to 0.5m diameter at the lower ende he quentity of vonter flowing is 900 libes/aconde If the at the higher and is 70kPa, find he gressure at the pressure Mover end. Soluton length =
If the difference between the liquid levels in two tanks (2.4 m) and pipe of (o.075m) diameter and (15 m) long used between them. What will be the volumetric flow rate of the fluid in the pipe. If fanning friction factor is (0.008) and liquid density 700 kg/m³ and dynamic viscosity 2.2x10-2kg/m.s and the flow was laminar,
Flow Characteristics( Entrance Effect) Why was there some disagrement between the actual Pitot tube velocity profile and the power law velocity profile?