Water flow from a large tank (T1) through a pipe Pipe X which splits into two smaller pipes, which discharges and flow out freely on Pipe Y and Pipe Z on as shown on the figure below. • Diameter of Pipe W and Pipe X =50 mm • Diameter of Pipe Y = 30 mm • Diameter of Pipe Z = 20 mm The velocity in meter per second through Pipe X is Blank 1 m/s. ***EXPRESS YOUR ANSWER in TWO (2) DECIMAL PLACE and DO NOT PUT UNITS*** T-1 Pipe Y 7m 4m Pipe Pipe W Pipe Z

Water flow from a large tank (T1) through a pipe Pipe X which splits into two smaller pipes, which discharges and flow out freely on Pipe Y and Pipe Z on as shown on the figure below. • Diameter of Pipe W and Pipe X =50 mm • Diameter of Pipe Y = 30 mm • Diameter of Pipe Z = 20 mm The velocity in meter per second through Pipe X is Blank 1 m/s. EXPRESS YOUR ANSWER in TWO (2) DECIMAL PLACE and DO NOT PUT UNITS T-1 Pipe Y 7m 4m Pipe Pipe W Pipe Z

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe P1 450mm in diameter, branches into two pipe (2 & 3) of diameters 300mm & 200mmrespectively. If the average velocity in the 450mm diameter pipe is 3m/s. Find; i) Discharge through the 450mm diameter pipe. ii) velocity on the 200mm diameter of pipe, of the average velocity in the 300mm pipe is 2.5m.
Exercise [2] As shown in Figure below, the velocity of water, v (m/sec), discharged from a cylindrical tank through a long pipe can be computed as: (/2gH V2gH tanh 2L V = L. Where g=9.81 (m/sec?), H=initial head (m), L= pipe length (m), and t = elapsed time (sec). Determine the head needed to achieve v= 5 m/sec in 2.5 seconds for a 4-m-long pipe by Newton-Raphson method. Use ɛ= 1%.
Solve and draw also the figures. i. Water is flowing through a pipe of 100 mm diameter under a pressure of 19.62 N/cm² (gauge) and with mean velocity of 3.0 m/s. Find the total head of the water at a cross-section, which is 8 m above the datum [Ans. 28.458 m] ii. A pipe, through which water is flowing is having diameters 40 cm and 20 cm at the cross-sections 1 and 2 respectively. The velocity of water at section 1 is given 5.0 m/s. Find the velocity head at the sections 1 [Ans. 1.274 m ; 20.387 m ; 0.628 m³/s] line. and 2 and also rate of discharge. The water is flowing through a pipe having diameters 20 cm and 15 cm at sections 1 and 2 respectively. iii. The rate of flow through pipe is 40 litres/s. The section 1 is 6 m above datum line and section 2 is 3 m above the datum. If the pressure at section 1 is 29.43 N/em², find the intensity of pressure at section 2. [Ans. 32.19 N/cm²]
44. Pipe 1, branches to three pipes as shown in the given figure. The areas and corresponding velocities are as given in the following table. The value of V, in cm per second will be Velocity Area Pipe 1 (cm per second) (sq cm) 3 1. 50 20 2. V2 10 4 3. 30 15 4. 20 10
The fireman wishes to direct the flow of water from his hose to the fire at B.(Figure 1) Figure -35 ft- B 20 ft Part A Determine two possible angles 0₁ and 2 at which this can be done. Water flows from the hose at VA = 45 ft/s. Enter your answers numerically separated by a comma. Assume angles below the horizontal as positive. 01, 02 = Submit Provide Feedback % ΑΣΦΗ ΤΗ ↓↑ Request Answer vec ? Next >
Keeping in mind continuity of flow, compute the velocity of flow for section C (Vc), the 6 inch pipe. 4 Section 20 in 3 fps QA Qe Qc Section Vo. 5 fps ते Vc = 1 FIGURE 2.12 Illustration for Example 2.10. 4 in 98 Section с 6in. Qc You should round to the nearest 2 places after the decimal throughout your work. For example 0.089 should round to 0.09 and 0.082 should round to 0.08. Your answer must have 2 places after the decimal. For example: 30.24 or 3.80. 12 inches 1 ft Answers are numerical only, no units required.
Time (s) 8. Consider the piping system shown. The average speed of water flowing through the 12-inch-diameter section of the piping system in 5 ft/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in ft /s and gpm. For the case of steady flow of water through the piping system, what is the average speed of water in the 6-inch-diameter section of the system? 12 in. 5 ft/s 9. By what factor do you increase the resistance to bending (about x-x axis) if you were to use W18x76 beam over W8x31? (Search for the inertias of W sections)
The branched pipe as shown in figure below discharges water. The diameters of the pipe 1 is 1.5 cm, pipe 2 is 3 cm & pipe 3 is 4 cm. The discharges in pipe 1 is 21 lit/sec, pipe 2 is 26.25 lit/sec. Find the discharge in pipe3 in Lt/sec, velocity in pipe 2 m/s & velocity in pipe 3 if the diameter of pipe 3 is 4 cm. (ENTER ONLY THE VALUE IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET. ALSO UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) Pipe 1 Pipe 3 Pipe 2 The discharge in pipe 3 (in Liter/sec) = The velocity of water in pipe 2 (in m/s) = The velocity of water in pipe 3 (in m/s) =
a) Hydraulic systems commonly have a pump that produces a constant flow rate. Assuming the fluid is incompressible, this situation is known as steady flow or continuity flow. Referring to Figure Q3 (c) the fluid flows at a velocity of 3 m/min at point Q1. The diameter at point Q1 is 50 mm and the diameter at point 2 is 40 mm. In applying the continuity equations, determine the flow velocity at point Q2. Further determine the flow rate in g.p.m (gallon per minute), given 1 gallon = 0.00378 m³. Figure Q3 (c)
Water flows through a 125 mm diameter pipe at a velocity of 7.5 m/sec. Find the mass flow rate in kg/sec. NOTE: Do not write any unit to your answer, put your answer in a numerical form only and use up to 3 decimal places. ASAP PLS
b) Water flows through a pipe as shown in Figure 1 at the rate of 80 L/s. If the pressure at Point 1 is 180 kPa; r2 = 8 cm 2 m ņ = 16 cm Figure 1 i. What is the velocity of water at Point 1? ii. What is the velocity of water at Point 2? iii. Calculate the pressure at Point 2.
The equations describing the position of a water stream (with respect to time) coming out of the hose, shown in the following figure, are given by the following. y X (Vy)o = 1.5 m/s Hose -Xo = 2m x = x₁ + (Vx) ot y = Y₁ + (V₂) ot — — — gt² 2 V (V₂) = 2.6 m/s Yo = 1.5 m In these relationships, x and y are position coordinates, x and y are initial coordinates of the tip of the hose, (Vx) and (V₂) are the initial velocities of water coming out of the hose in the x- and y-directions, g = 9.81 m/s², and t is time. Plot the x- and y-positions of the water stream as a function of time. Also, plot the path the water stream will follow as a function of time. Compute and plot the components of velocity of the water stream as a function of time. (Submit a file with a maximum size of 1 MB.)