Water Flow into horizontal pipe with velocity of v. Determine the horizontal and vertical component of force and the moment at A need to hold the elbow in place. Neglected the weight of the elbow and the water within it. Take v between 1 to 5 m/s and D1 between 0.2 to 1.0 m and D2 between 1.0 to 0.2 m. 3 m D1 v1 A В

Water Flow into horizontal pipe with velocity of v. Determine the horizontal and vertical component of force and the moment at A need to hold the elbow in place. Neglected the weight of the elbow and the water within it. Take v between 1 to 5 m/s and D1 between 0.2 to 1.0 m and D2 between 1.0 to 0.2 m. 3 m D1 v1 A В

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.114P: Determine the resultant force acting on the elbow of the thin-walled pipe when the pipe carries a...

See similar textbooks

Similar questions

Water discharges into the atmosphere through the device shown in the picture. Determine the strenght component in the x direction on the flange required to mantain the device on it's place. Ignore the effect of gravity and friction. Express the result in lb.
Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 60o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be neglected.
When the pressure heads at A and B are 3.0 m and 90.0 m, respectively, pumps AB is communicating a power of 100 HP to the system. What elevation can be maintained in reservoir D?
Q2 The truck dumps water on the ground such that it flows from the truck through a 100-mm-wide opening at an angle of 60°. The length of the opening is 2 m. Determine the friction force that all the wheels of the truck must exert on the ground to keep the truck from moving at the instant the water depth in the truck is 1.75 m. A 1.75 m B 60°
Water flows through the curved pipe shown in the figure below where point X denotes the center of gravity of the system. Considering the weight of the pipe and water with-in as Wg which acts at a distance of Xm from pipe axis, answer the following questions: 1) What are the horizontal and vertical components of the force provided by the flange at point A? 2) What is the moment provided by the flange at point A? Patm D2 H D1 A L Following data is given: Q = 1m³ /s D1 = 0.5 m D2 = 0.25 m X — 0.1 т L 1.5 m Н — 2 т WG = 1000 kg
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
find reynolds
Water is flowing upward through a tapering pipe of height 1 m at the rate of 0.28 cumec. Thediameters at the lower and upper ends of the pipe are 300 mm and 600 mm, respectively. If pressure atthe lower end of the pipe is 0.981 bar, determine the force exerted on the tapering pipe and itsdirection. Neglect the losses of energy and the weight of the pipe.
Determine the resultant force acting on the elbow of the thin-walled pipe when the pipe carries a uniform internal pressure p0.
A fan in the duct shown below sucks air from the ambient and expels it as a jet at 1 m/s to the ambient. Determine the gauge pressure at the point marked as A. Take the density of air as 1 kg/m3. 1 m/s A-
One end/side of the pipe is positioned on level (h1) and the other is tilted upward at a height h2.The pressure values of fluid within this pipe, both on level and up, are measured as P1 and P2.If the fluid flow is kept at constant speed,use Bernoulli’s principle to show that pressure of the fluid inside the pipe tilted upward, P2, is given by: P2=P1 -ρgh2
A sluice gate, which controls flow rate in a channel by simply raising or lowering a vertical plate, is commonly used in irrigation systems. A force is exerted on the gate due to the difference between the water heights y1 and y2 and the flow velocities V1 and V2 upstream and downstream from the gate, respectively. Take the width of the sluice gate (into the page) to be w. Wall shear stresses along the channel walls may be ignored, and for simplicity, we assume steady, uniform form flow at locations 1 and 2. Develop a relationship for the force FR acting on the sluice gate as a function of depths y1 and y2, mass flow rate m ., gravitational constant g, gate width w, and water density ? .