Water with density Pwater = 1000 kg/m³ flows through a pipe, composed of two reduced in size sections, as shown on the figure. The two sections are linked with a flange connection, and the corresponding diameters are D, = 8 cm and D, = 5 cm. If the velocity in cross-section 1 is v, = 5 m/s, and the readings of the connected liquid manometer is h = 60 cm, determine the reaction force acting over the flange connection. The manometric fluid is mercury, with density Pa-101kPa %3D %3D Mercury Pmercury = 13600 kg/m³.

Water with density Pwater = 1000 kg/m³ flows through a pipe, composed of two reduced in size sections, as shown on the figure. The two sections are linked with a flange connection, and the corresponding diameters are D, = 8 cm and D, = 5 cm. If the velocity in cross-section 1 is v, = 5 m/s, and the readings of the connected liquid manometer is h = 60 cm, determine the reaction force acting over the flange connection. The manometric fluid is mercury, with density Pa-101kPa %3D %3D Mercury Pmercury = 13600 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
An oil jet (S.G = 0.8) is hitting a fixed vane at flow rate of 0.3 m³/s as shown in the figure. The values of V1 = 20.7 m/s and V2 = 6.21 m/s. What is the external reactions in the x-direction needed to hold this fixed vane? Assume water density = 1000 kg/m³. V₂ S 120°
A jet of air having velocity V₁ and cross-sectional area A₁ strikes an inclined plate as shown in the figure. Neglect any effects of viscosity. V₁ (a) Find V₂ and V3 in terms of V₁. Note that the pressure is patm everywhere. (b) Because viscous effects are negligible, there is no way for the air to exert a force on the plate in the tangential (z) direction. Using the coordinate system in the figure, find A₂ and A3 in terms of A₁ and 0. (c) For V₁ = 50 m/s, A₁ = 5 x 10-4 m², and 0 = 60°, find the force required to hold the plate in place. Neglect the weight of the plate. Recall that pair = 1.225 kg/m³.
The reduced elbow shown in the figure is part of a distribution system for a fluid whose density is 0.85 and which is in a vertical plane. If the manometer at point 1 indicates 245 kPa, and the flow rate at point 1 is 0.060 m/s. a) Calculate the reactions at "x" and "y" at A to keep the elbow in place
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
A pressurized tank of water is used to create a fountain, as illustrated. Assume that the water's free surface area in the tank is very large relative to the pipe's cross-sectional area, which is circu- lar with diameter d 1.0 cm. The small pipe bend has height = 10.0 cm. At the instant when 0.75 m, H = 2.5 m, and the gauge measures a pressure of Pgauge 20.0 kPa, the water spray reaches a height L above the pipe exit. h = = = Neglecting viscous effects, determine the height of the spray, L.
According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
The open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V, for the given data V, = 3 m/s and Q3 = 0.01 m/s. Q -0.01 ms D, =5 cm D3 =7 cm Water
A conveyer belt is installed in a process industry to move the product from bottom to top. Anincompressible, viscous fluid is placed between the upper and lower belts to avoid the friction andcool down the surface of belt. The belts are aligned at an angle θ and moving in opposite directionwith constant velocities V1 and V2, as shown in figure. Assume the laminar flow with no pressuregradient and gravity acting vertically downward. Calculate:a. Velocity profile in the fluidb. Volume flow rate between the beltsc. Shear force per unit area acting on bottom belt Note: Enlist all the assumptions you have taken to solve the problem and clearly mention theboundary conditions.
60mm water jet strikes a plate containing a hole of 40mm diameter as shown in figure. Density of water is 1000kg/m^3. Determine magnitude of the force required to hold the plate.
A 0.4 m-diameter pipe bend shown in the diagram is carrying crude oil (S = 0.65) with a steady flow with velocity of 3 m/s. The bend has an angle of 30° and lies in a vertical plane. The volume of oil in the bend is 1.2 m3, and the empty weight of the bend is 4 kN. Assume the pressure along the centerline of the bend is constant with a value of 85 kPa gage. Water density = 1000 kg/m3, g= 9.81 m/s?, Patm = 100 kPa, frictionless flow. Answer the following: Bolted flange Flow 30 The net pressure force along the horizontal direction (N). Net out flow rate of momentum through the control surface (N) in the horizontal direction. Absolute value.