What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite set of arithmetic or logical operations. 2. A small computer on a single integrated circuit containing a processor core, memory, and programmable input/output peripherals. 3. An electromechanical device that converts electrical energy into mechanical energy. 4. An electronic circuit that enables a voltage to be applied across a load in either direction. 5. A device that supplies electric power to an electrical load.

What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite set of arithmetic or logical operations. 2. A small computer on a single integrated circuit containing a processor core, memory, and programmable input/output peripherals. 3. An electromechanical device that converts electrical energy into mechanical energy. 4. An electronic circuit that enables a voltage to be applied across a load in either direction. 5. A device that supplies electric power to an electrical load.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter22: Basics Of Electronics And Computer Systems

Section: Chapter Questions

Problem 4RQ: Means that data concerning the effects of the computers commands are fed back to the computer as an...

See similar textbooks

Similar questions

[2.2] Consider two different implementations of the same instruction set architecture. instructions can be divided into four classes according to their CPI (classes A, B, C, and D with a clock rate of 2.5 GHz and CPIs of 1, 2, 3, and 3, and P2 with a clock rate of 3 GHz CPIs of 2, 2, 2, and 2. Given a program with a dynamic instruction count of 1.0E6 instruc divided into classes as follows: 10% class A, 20% class B, 50% class C, and 20% cla which is faster: P1 or P2? a. What is the global CPI for each implementation? Ans. 2.6, 2.0 b. Find the clock cycles required in both cases. Ans. 26 x 105, 20 × 10³
What is the major difference between ROM and RAM memory in a microprocessor?
The instructions and question are provided below: 1. Draw a sketch of the situation, label initial and final positions and times. 2. Draw a loop and identify objects in the system and objects in the environment 3. Draw an energy-bar chart for the initial and the final situations 4. Write down the work-Energy equation Kf +Ugf+Usf+DeltaEth = Ki +Ugi +Usi +W 5. Solve for "To Find/ Unknown " quantities 80. ||||| INT In a physics lab experiment, a spring clamped to the table shoots a 20 g ball horizontally. When the spring is compressed 20 cm, the ball travels horizontally 5.0 m and lands on the floor 1.5 m below the point at which it left the spring. What is the spring constant?
An industrial robot performs a machine loading and unloading operation. A PLC is used as the cell controller. The cell operates as follows: (1) a human worker places a part into a nest, (2) the robot reaches over and picks up the part and places it into an induction heating coil, (3) a time of 10 sec is allowed for the heating operation, and (4) the robot reaches into the coil, retrieves the part, and places it on an outgoing conveyor. A limit switch X1 (normally open) is used to indicate that the part is in the nest in step (1). This energizes output contact Y1 to signal the robot to execute step (2) of the work cycle (this is an output contact for the PLC, but an input interlock signal for the robot controller). A photocell X2 is used to indicate that the part has been placed into the induction heating coil C1. Timer T1 is used to provide the 10-sec heating cycle in step (3), at the end of which, output contact Y2 is used to signal the robot to execute step (4). Construct the ladder…
1) A slider-crank mechanism is a planar mechanism that performs a conversion between the translational motion of a slider and the rotational motion of a crank. It is used in many different engineering applications. A familiar example will be a piston engine. In Figure 1, a basic slider- crank mechanism is shown. В b dạc Figure 1. A basic slider-crank mechanism 0< 0< 2n; b = 20 cm; I= 50 cm 1- Find the angle of Ø and the distance of dAC as a function of 0. 2- If crank AB has a rotational speed of w = 1000 rev/min; find velocity of C (Vc) and velocity and acceleration of link BC (vBC & aBC)
a. Currently, you serve as a robotic engineer by a company, and your boss want you to design a robot in spatial space to satisfy the following conditions: i. Max reachable distance of the robot is 1 meter. ii. Only using revolute joints, connecting links and rigid load bearing links (the length of link is 0.5m). iii. The degree of freedom (Dof) of the robot is 2. What is your design, how many joints and links will you use? b. The payload of your design is 10 kg (each load bearing link can hold 5 kg, 5 kg+5 kg=10kg, the weight and payload of the connecting links will be ignored), but your boss wants your designed robots to handle 20 kg payload. How will you update your current design, and how many joints and links will you use in the new design? What is the Dof of the new designed robot.
exam_question.php?exam_id: Some computers contain multi-processors in order to s1 /4 MS-DOS considered as the weakest OS because of It
Machine Theory Question-3: Determine the degrees of freedom of the following mechanism. Write down how many inputs there should be in the mechanism and which of these inputs could be.
The figure to the right shows a schematic of a SCARA robot. A Answer the following: A1 What does SCARA stand for? (2] A2 How many degrees of freedom does a SCARA robot have? (2]
Q1. a) List two examples of open-loop systems in practice and explain why these are open-loop systems. List two examples of closed-loop systems in practice and explain why these are closed-loop systems. b) Explain why closed-loop systems are more accurate.
Means that data concerning the effects of the computers commands are fed back to the computer as an input signal.
Application first order