A power cycle consisting of the three processes: Process 1-2: Constant volume to P2 Process 2-3: Polytropic expansion Pv=c, use k=1.28 Process 3-1: Compression at constant pressure Assuming 2.5 kg carbon dioxide as the working substance with P₁= 1.5 bar, P₂= 6 bar, T₁=350 K and neglecting kinetic and potential energy effects: a) sketch cycle in P-v diagram b) calculate thermal efficiency CO₂ molar mass = 44. CO2 specific heat cy=1.014 kJ/kg/K

A power cycle consisting of the three processes: Process 1-2: Constant volume to P2 Process 2-3: Polytropic expansion Pv=c, use k=1.28 Process 3-1: Compression at constant pressure Assuming 2.5 kg carbon dioxide as the working substance with P₁= 1.5 bar, P₂= 6 bar, T₁=350 K and neglecting kinetic and potential energy effects: a) sketch cycle in P-v diagram b) calculate thermal efficiency CO₂ molar mass = 44. CO2 specific heat cy=1.014 kJ/kg/K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a piston-cylinder assembly, there is initially a pressure of 300 kPa, a temperature of 150oC and a volume of 0.5 m3 of air. Until air doubles in volume with PVn=constant polytropic processexpands as much. For n =1, n = k and n = 1.6a. final pressure of the air,b. Moving border work,c. Calculate the heat transfer.(Note: take constant specific heat values at room temperature (at 300 K).)
2. A gas undergoes a thermodynamic cycle consisting of the following processes:i) Process 1-2: Constant pressure p1 = 1.4 bar, V1=0.028 m3, W1-2=10.5 kJii) Process 2-3: Compression with pV=Constant, U3=U2iii) Process 3-1: Constant Volume, U1-U3 = -26.4 kJThere are no significant changes in KE and PEi) Sketch the cycle on a p-V diagramii) Calculate the network for the cycle in kJiii) Calculate the heat transfer for process 1-2iv) Show that ƩW = ƩQ
An automobile industry using piston cylinder arrangement for their operation it under goes a thermodynamic cycle which includes three processes with an initial state where pressure is 1.5 bar, volume is 2 m3 and internal energy equals to 480 kJ. The processes are as follows: 1)first stage to second stage: Compression with pV equals to constant to p2 is equals to 2 bar, U2 equals to 720 kJ 2)Second stage to third stage: work is equals to zero, and Q2-3 = - 150 kJ 3)Stage third to one: work is equals to 75 kJ. Neglecting kinetic energy and potential energy changes, find the heat transfer Q1-2 and Q3-1.
Q.1 A piston-cylinder device operates 1 kg of fluid at 20 bar pressure. The initial volume is 0.1 (the last digit of your id.no). The fluid is expand reversibly following the process pv¹.3 = constant. at point B the volume becomes 1.5 m³. The fluid is then cooled at a constant temperature. Calculate the work done in the cycle. p (bar) 0.1 last digit of your id. no 0.1 v cu.m Py ¹.3 B 1.5
20 g of air undergoes a closed cycle, illustrated in Figure Q2, which consists of the following 3 processes: 1-2 Constant pressure heat rejection. 2-3 Constant volume heat addition. 3-1 Isothermal expansion back to the original conditions. P (kPa) 75 1 V (m') 0.025 0.04 Figure Q2: Three process cycle Given that Rair = 287 J/kg-K, and Cy = 718 J/kg-K, and assuming ideal gas conditions throughout: (a) Determine the temperatures at points 1, 2 and 3, and the pressure at point 3. (b) Determine the work during each process, and the net work from the cycle. (c) Determine the heat transferred during each process. (d) Verify that this is a cycle.
Two kilograms of air within a piston-cylinder assembly execute a Carnot power cycle with maximum and minimum temperatures of 750 K and 300 K, respectively. The heat transfer to the air during the isothermal expansion is 60 kJ. At the end of the isothermal expansion the volume is 0.4 m³. Assuming the ideal gas model for the air, determine ) the work and heat transfer for each of the four processes, in kJ. ) Sketch the cycle on p-V coordinates.
4. (It's impossible for a heat engine to produce net work in a complete cycle if it exchanges heat only with bodies at a single fixed temperature). this statement refer to: A. 1 law of thermodynamic B. 2nd law thermodynamic C. Gibss-Dalton law 5. The cycle consist of two isothermal processes joined by two adiabatic process is called: A. Carnot cycle B. Refrigeration cycle C. Gas turbine cycle 6. Steam at 800 kPa, 300°C is throttled to 200 kPa. The final temperature will be: A. 292 °C B. 302 °C C. 298 °C
10. Figure shows a power cycle executed by a gas in a piston-cylinder assembly. For process 1-2, Uz - Ui = 15 kJ. For process 3-1, Q=10 kJ. There areno changes in kinetic or potential ener gy. Determine (a) the work for each process, in kJ, (b) the heat transfer for processes 1-2 and 2-3, each in kJ , and (c) the ther mal efficiency. 4. 2 (kPa) 1 4. V (m³)
Referring to the reversible heat pump cycle shown in the figure, p1 = 14.7 Ibf/in?, p4 = 27.8 lbf/in?, v1 = 12.6 ft³/Ib, v4 = 8.0 ft³/lb, and the gas is air obeying the ideal gas model. P4 pi TH V4 VI Determine TH, in °R, and the coefficient of performance. Step 1 Determine TH, in °R. TH = °R Save for Later Attempts: 0 of 1 used Submit Answer Step 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
SU-1 A heat engine with &=0.400 operates between two heat reservoirs at 250K and 450K. The energy amounts and heat flow diagram for one cycle of operation of the engine is shown to the right. a) What is the change in entropy for the engine for one cycle of operation of the engine? b) Find the change in entropy for the engine surroundings for one cycle of operation of the engine. c) Find the change in entropy for the universe for one cycle of operation of the engine. d) Is this engine real, reversible, or impossible? Explain why using your results from the previous parts. Th-450K 500 200J Engne 300J T-250K
2.Find the minimum work done per Kg of air in a cycle according to the following processes: a. Isothermal expansion from state 1 to state 2. b. Constant volume compression from state 2 to state 3. c. Constant pressure compression from state 3 to the initial state. Data: P1= 350 KPa V1 = 1 m3 /Kg T3 = 16500 C d. Represent the work on a p-V diagram.
1. A gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processes: Process 1-2: Compression with PV = constant, from P₁ = 1 bar, V₁ = 2 m³ to V₂ = 0.2 m³, U₂ − U₁ = 100 kJ; 2 Process 2-3: Constant volume to P3 = P₁; Process 3-1: Constant-pressure and adiabatic process. Neglect the changes of kinetic and potential energy in all three processes. (a) Sketch the cycle on a P-V diagram; (b) Determine the net work (i.e., W12 + W23 + W31) of the cycle, in kJ; (c) Determine the heat transfer for process 2-3, in kJ. Hint: System's state variables remain unchanged after a cycle, i.e. (U₂ − U₁) + (U3 − U₂) + (U₁ − U3) = 0