Which correctly describes the application of the photoelectric effect on the operation of photovoltaic cells? O The frequency of light waves striking a surface determines if electrons are released. O The current generated is used to convert electrical energy into heat energy. O Light waves striking a surface eject electrons from the innermost shell of the surface's atoms. O The intensity of light waves striking a surface determines if electrons are released.

Which correctly describes the application of the photoelectric effect on the operation of photovoltaic cells? O The frequency of light waves striking a surface determines if electrons are released. O The current generated is used to convert electrical energy into heat energy. O Light waves striking a surface eject electrons from the innermost shell of the surface's atoms. O The intensity of light waves striking a surface determines if electrons are released.

Modern Physics

3rd Edition

ISBN:9781111794378

Author:Raymond A. Serway, Clement J. Moses, Curt A. Moyer

Publisher:Raymond A. Serway, Clement J. Moses, Curt A. Moyer

Chapter3: The Quantum Theroy Of Light

Section: Chapter Questions

Problem 43P

See similar textbooks

Similar questions

(a) Calculate the number of photoelectrons per second that are ejected from a 1.00-mm2 area of sodium metal by a 500-nm radiation with intensity I .30kW/m2 (the intensity of sunlight above Earth’s atmosphere). (b) Given the work function of the metal as 2.28 eV, what power is carried away by these photoelectrons?
A laser with a power output of 2.00 mW at a 400-nm wavelength is used to project a beam of light onto a calcium photoelectrode. (a) How many photoelectrons leave the calcium surface per second? (b) What power is carried away by ejected photoelectrons, given that the work function of calcium is 2.31 eV? (c) Calculate the photocurrent. (d) If the photoelectrode suddenly becomes electrically insulated and the setup of two electrodes in the circuit suddenly starts to act like a 2.00-pF capacitor, how long will current flow before the capacitor voltage stops it?
(a) Calculate the ionization energy for He+. (b) What is the minimum frequency of a photon capable of ionizing He+?
Vo, V Cs f. Hz The graph shows the stopping potential for photoelectrons as a function of the frequency of the incident light for two different metals (Cs and W). Which of the following statements is true? O The maximum kinetic energy of the photoelectrons increases as the frequency of the incident light increases. O The stopping potentials for all metals are the same. O For a given frequency of incident light, the photoelectrons from W are more energetic than those from Cs. O Because the intercepts are different, Planck's constant is not constant. O The threshold frequency for Cs is greater than that for W.
C Which choice in the list below corresponds to a correct unit of Planck's constant? O a. J/s O b. J.s² O c. eV.s d. eV/s
In an experiment to demonstrate the photoelectric effect, physics students allow light of various frequencies to fall on a metal surface in a photocell. The photoelectrons are decelerated across a retarding voltage, and the stopping potential, Vs, is measured for each frequency. The data they obtained is graphed in the image attached. The students use the data points on the graph to determine a value for the work function of the metal.a) Determine the magnitude and the unit of the work function for this metal surface.b) What is the maximum kinetic energy (in eV) of the photoelectrons produced when ultraviolet light of frequency 1.93x1016 Hz is incident on the metal surface?
15 Why we use cesium as a photo emissive surface ? Cesium has large number of electrons It has negative charge O It has low work function It emits electrons of same K.E
Consider the following. (a) Model the tungsten filament of a lightbulb as a blackbody at temperature 3320 K. Determine the wavelength of light it emits most strongly. Your response differs from the correct answer by more than 10%. Double check your calculations. nm
When developing a night vision night vision equipment, you need to measure the work function for the surface of a metal, so you perform a photoelectric photoelectric effect experiment. You measure the cutoff potential V0 as a function of of the wavelength À of light striking the surface. The results appear in the following table. In your analysis, you use c = 2.998 X 10^8 m/s and e = 1.602 X 10^-19 C, which are values obtained in other experiments. (a) Select a way to represent your results graphicallyso that the data points are close to a straight line. Using this graph, find the slope and the intercept y of the straight line that best fits the data. (b) Use the results from (a) to calculate the Planck constant h (as a test of your data) and the work function ( in and V) of the surface. ( c) What is the longest wavelength of light that will produce photoelectrons from this surface? (d) What wavelength of wavelength of light is required to produce photoelectrons with a kinetic energy…
d the change in frequency of a photon of red light whose original frequency is 7.3 x10 14 Hz when it falls through 22.5 2.8 Hz.A O 3.8 Hz.B O 1.8 Hz.c O find the change
The photoelectric effect in a cosmic context. Ultraviolet radiation striking dust grains composed of the moon’s dominant rock type, feldspar (with work function 4.5 eV), leaves them with a small electric charge. Smaller grains levitate due to the resulting electrostatic repulsion, giving the surface a diffuse dust halo. What sign of charge do the dust grains have?A. NegativeB. PositiveC. Some grains are negative, some are positive.
Light with a frequency of 3.73 x 1015 Hz strikes a metal surface and ejects electrons that have a maximum kinetic energy of 6.9 eV. What is the work function of the metal? Number i Units