h/2A 0.6-kg block rest on a horizontal frictionless surface as shown in the figure.The block is pressed back against a spring having a constant of k-500 N/m,compressing the spring by 15 cm to point A. Then the block is released.Use the conservation of Mechanical energy to solve the following:Find the energy stored in the spring?b) Find the velocity of the spring at the point passes x-0?Find the maximum height h the block travels up the frictionless inclineda)c)surfaceIf e= 30°?d) Find the distance d the block travel on the inclined surface?e) How fast (the velocity) is the block going when halfway (at h/2) to itsmaximum

given data: as per our guideline, we can give the answer to only three subparts of the question.…

wing h/2 A 0.6-kg block rest on a horizontal frictionless surface as shown in the figure. The block is pressed back against a spring having a constant of k=500 N/m, compressing the spring by 15 cm to point A. Then the block is released. Use the conservation of Mechanical energy to solve the following: Find the energy stored in the spring? b) a) Find the velocity of the spring at the point passes x-0? Find the maximum height h the block travels up the frictionless inclined C) surface If e= 30°? d) Find the distance d the block travel on the inclined surface? e) How fast (the velocity) is the block going when halfway (at h/2) to its maximum

wing h/2 A 0.6-kg block rest on a horizontal frictionless surface as shown in the figure. The block is pressed back against a spring having a constant of k=500 N/m, compressing the spring by 15 cm to point A. Then the block is released. Use the conservation of Mechanical energy to solve the following: Find the energy stored in the spring? b) a) Find the velocity of the spring at the point passes x-0? Find the maximum height h the block travels up the frictionless inclined C) surface If e= 30°? d) Find the distance d the block travel on the inclined surface? e) How fast (the velocity) is the block going when halfway (at h/2) to its maximum

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

In the system shown in the figure, mA = 2 kg and mB = 5 kg.the mass is connected to each other by rope. A 12 N Fforce is applied to body A at an angle of 10 °.There is only friction between body B and the inclined planeand the kinetic coefficient of friction is 0.3. a) Draw the free body diagram of each object. b) Find the acceleration of the system. g = 9.8 m / s ^ 2, sin (37 °) = cos (53 °) = 0.60, cos (37 °) = sin (53 °) = 0.80, sin (10 °) = 0.17,cos (10 °) = 0.98
The friction coefficient between the 3kg object and the 2kg blocks in the figure is 0.3. the horizontal plane and the rollers are frictionless and the masses move from rest. a) Find the acceleration of each blokları by showing the forces acting on each block (free body diagram). b) Find the tension in the ropes. (g = 3,8m / s^2)
A ring of mass m is attached to the spring and slides over the rod. Unextended length of the spring l0 and the spring coefficient is k. When the collar is at point C, it is released and between the collar and bar Since the coefficient of friction is μk; a)Find the velocity of the ring at points A and B using the Work-Energy method. b)Find the normal forces acting on the collar at points A and B.
A ring of mass m is attached to the spring and slides over the rod. Unextended length of the spring l0 and the spring coefficient is k. When the collar is at point C, it is released and between the collar and bar Since the coefficient of friction is μk; a) Find the velocity of the ring at points A and B using the Work-Energy method. b) Find the normal forces acting on the collar at points A and B.
Given the figure before, when the displacement of block D is 360 ft, then the displacement of block A is closest to:
2.7 A force P = 200N acts on a 50kg crate beginning from t = 0 as shown in the figure. The coefficient of kinetic friction between the crate and the ground is = 0.3. Find the (a) acceleration of the crate and (b) the velocity of the crate at t = 3s. 30⁰
A block of mass m = 2.00 kg is attached to a spring of force constant k = 555 N/m as shown in the figure below. The block is pulled to a position x, = 4.90 cm to the right of equilibrium and released from rest. x= 0 x= x; (a) Find the speed the block has as it passes through equilibrium if the horizontal surface is frictionless. m/s (b) Find the speed the block has as it passes through equilibrium (for the first time) if the coefficient of friction between block and surface is u, = 0.350. m/s
The figure shows three forces applied to a trunk that moves leftward by 2.63 m over a frictionless floor. The force magnitudes are F1 = 5.16 N, F2 = 8.74 N, and F3 = 3.23 N, and the indicated angle is 0 = 60°. (a) During the displacement, what is the net work done on the trunk by the three applied forces, the gravitational force, and the normal force? (b) Is there a net transfer of energy to or from the trunk? (c) Does the kinetic energy of the trunk increase or decrease?
An electric elevator with a motor at the top has a multistrand cable weighing 8.4 lb/ft. When the car is on the first floor 270 feet of cable are paid out, and effectively 0 feet when the car is on the top floor. How much work does the motor do to lift an 1800 lb car and cable from the first floor to the top? Provide a picture model, give the approximate equation, then solve.
R1 R2 R3 P) For the given pulleys compound system : (a) Find the Ideal Mechanical Advantage (IMA) (b) The required applied force (F) to lift 450 N load F: Applied load (c) The anchor reactions (R1, R2 and R3) (d) the movement acceleration of the load (e) Resketch the given pulleys system and label the tension force value in each part (line) of the rope. 450 N Compound Systems
A car weighs 150 kilograms with a center mass at G. The horizon force P= 600 newton’s. Please find the normal force of every wheel and the change in velocity. Please draw the free body diagram if necessary. Please refer to illustration. Thank you. G 1.25 m P = 600 N %3D 0.25 m 0.25 m 0.5 m -1.25 m |0.75 m
For the system shown in figure, find the time required to fill the cylindrical tank (D-60cm) if. V-3m/s, Di-2cm, V-5m/s, D,-6cm, and V3-7.2m/s, Dy-5cm. h=1.2m