Wolverine has an arm that is 1[m] long and claws that are0.5[m] long. He's trying to knock over a wall. His shouldercan exert a torque of 1,500[N-m]. What is the ratio of forceon the wall with vs without his claws extended?1.5[m]pointPivotF/FAdamantiumWallwithoutwithclawsclawsA.2/3FWolverinewithВ.3/2with clawsС.11.0[m] PivotAdamantiumD. I don't know but the torque direction ispointWallE. I don't know but the torque direction isFwithoutWolverineBare hands

Answered: Image /qna-images/answer/c2b9bc12-66cc-4714-9b65-cb7d63088a9d.jpg

Wolverine has an arm that is 1[m] long and claws that are 0.5[m] long. He's trying to knock over a wall. His shoulder can exert a torque of 1,500[N-m]. What is the ratio of force on the wall with vs without his claws extended? 1.5[m] point Pivot F with claws without claws Adamantium Wall А. 2/3 F Wolverine with В. 3/2 with claws С. 1 1.0[m] Pivot Adamantium D. I don't know but the torque direction is point Wall E. I don't know but the torque direction is Fwithout Wolverine Bare hands

Wolverine has an arm that is 1[m] long and claws that are 0.5[m] long. He's trying to knock over a wall. His shoulder can exert a torque of 1,500[N-m]. What is the ratio of force on the wall with vs without his claws extended? 1.5[m] point Pivot F with claws without claws Adamantium Wall А. 2/3 F Wolverine with В. 3/2 with claws С. 1 1.0[m] Pivot Adamantium D. I don't know but the torque direction is point Wall E. I don't know but the torque direction is Fwithout Wolverine Bare hands

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 90A

See similar textbooks

Similar questions

What three factors affect the torque created by a force relative to a specific pivot point?
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
When opening do you push on it perpendicularly with a force of 55.0 N at a distance of 0.850 m from the hinges. What torque are you exerting relative to the hinges?
Check your Understanding Repeat Example 12.3 using the left end of the meter stick to calculate the torques; that is by placing the pivot at the left end of the meter stick.
What three factors affect the torque created by a force relative to a specific pivot point?
1. To tighten a bolt, you push with a force of 100 Nat the end of the wrench handle that is0.5 m from the axis of the bolt. (a) What torque are you exerting? (0.5M)(100N) = 50n/m of Torque (b) If you move your hand inward to be only 0.2 m from the bolt, how much force do youneed to exert to achieve the same torque? (0.8M)(100N) = 80n/m-50n/m = 30n/m more (c) Do your answers depend on the direction of your push relative to the direction of thewrench handle? Yes (90 degrees) perpendicular
O F You push on a door 18 cm from the hinge with a force F that has components Fx=7 Newtons and Fy=17 Newtons (see figure). What is the magnitude of the torque about the hinge? Answer in Nm.
My book has the answers as a) 10N b) 196N But I can't figure out the proper way to work it out. I figured you start by using torque and the weight of the board plus the forces of each support to make a equation for Fn1. Then once you solve for it go back and make a equation for Fn2. But I'm not getting the answers in my book when I do this.
onsldered a lever that can generaté torques. The bice he elbow as show. The bicep is capable of producing a N 00 700 N 45 5.0 cm (a)
1.A vault is opened by applying a force of 300 N perpendicular to the plane of the door, 0.80 m from the hinges. Find the torque due to this force about an axis through the hinges.a. 120 N⋅mb. 240 N⋅mc. 300 N⋅m d. 360 N⋅m2.A meter stick is supported by a knife-edge at the 50-cm mark. Doug hangs masses of 0.40 and 0.60 kg from the 20-cm and 80-cm marks, respectively. Where should Doug hang a third mass of 0.30 kg to keep the stick balanced?a. 20cmb. 70cm c. 30cm d. 25cm3.A copper wire of length 2.0 m, cross sectional area 7.1 × 10−6 m2 and Young's modulus 11 × 1010 N/m2 has a 200-kg load hung on it. What is its increase in length? (g = 9.8 m/s2)a. 0.50 mmb. 1.0 mmc. 2.5 mm d. 5.0 mm
10kg rigid beam that is 3mlong is supported at each end. An8kg block is placed 2m fromsupport 1. How much upward forcedoes each support provide to ensurezero acceleration and zero torque?Note, if an object is not rotating, itis not rotating about every axis.
Two blocks, each of mass 2 kg are suspendedfrom the ends of a rigid massless rod of lengthL. The rod is held horizontally on the fulcrumand then released. The length L1 is 15 cm andthe length L2 is 85 cm. Draw the force diagram for the rod. Clearly label all forces. Write Newton’s 2nd Law equation: (for F of y) Write Newton’s 2nd Law equation: (for net torque) What is the magnitude of the linear acceleration of the block closest to the fulcrum? What is the magnitude of the linear acceleration of the block furthest from the fulcrum?