You are going to load a trailer similar to the one below with an aircraft engine that has a mass of 1,017 kg. The length of the trailer from the hitch to the axle is 274 cm. The center of mass of the trailer body is 73.7 cm in front of the axle and it has a mass of 117 kg. If the fraction of weight supported by the hitch can be no more than 119 kg, what is the furthest in front of the axle you can position the center of mass of the engine?

You are going to load a trailer similar to the one below with an aircraft engine that has a mass of 1,017 kg. The length of the trailer from the hitch to the axle is 274 cm. The center of mass of the trailer body is 73.7 cm in front of the axle and it has a mass of 117 kg. If the fraction of weight supported by the hitch can be no more than 119 kg, what is the furthest in front of the axle you can position the center of mass of the engine?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.17P: A man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an...

See similar textbooks

Similar questions

Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.
A 100 kN block is on a plane inclined at an angle of 30° with the horizontal. Find the parallel component of the weight of the block with the plane. .
1. What's the difference between the center of gravity and the center of mass? 2. How is the specific weight of a body defined? 3. What does it mean when we say a body is homogeneous? 4. What are the theorems of Papus and Guldinus used for?
The meterstick shown is 100 cm long. It is free to pivot around its center of gravity (CG), which is at the 50 cm mark. There is a 25.0 N block hanging from the 80 cm mark. Decide where each of the other blocks should be placed, one at a time, to balance out the 25.0 N block. At what mark on the meter stick would you place a 18.0 N block to balance the 25.0 N block?
An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load. Her crane has a 15K chassis and 35K counterweight. Assume all other parts of the crane have negligible weight. Answer all questions relative to the rotation point. How much torque is caused by the load? How much torque is caused by the chassis? How much torque is caused by the counterweight? What is the normal force on the rear (right) outriggers? What is the normal force on the front (left) outriggers? *each box in picture = 5 ft
A hand truck and its load, as shown below, have a mass of 100kg, and their centre of gravity (together) is at point C. What force F must the delivery person exert at the handles A of the hand truck to move it up the hill? Hint: In what direction is the force at the axle? Bonus question: How could the delivery person reduce the magnitude of the force they must exert? 0.7 0.55 * U 0.15 25° 0.8
A ship with a mass of 2000 tons and the value of I is 5840 m4. The density of sea water 1025 kg/m3. A container with a mass of 12 tons is displaced 6 m off the centre of the ship. This causes the ship to tilt 20. Assume the container is more or less on the same height as the centre of gravity of the ship. Determine 1. The metacentric height of the ship. 2. The height of centre of gravity of ship above the centre of buoyancy
A uniform sheet of metal 6ft square weighs 60lb. If the following weights are hung on each corner of the square in a consecutive manner: 20Ib at A, 60lb at B, 80lb at C, & 40lb at D, find the center of gravity of the system.
The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of the fulcrum. The hook which carries the load,weights 4kg and is also attached on the left-hand side of the fulcrum at a distance of 12cm.if graduation mark 72cm from the fulcrum reads 50kg. Find (a).the weight of rider (b). How far is the zero graduation from fulcrum (c).What is the movement of riderper kg of graduation?
In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?
You have a summer internship at NASA and are working on plans for a new space station to be launched into orbit around the Earth. The design of the space station is shown. It is to be constructed in the shape of a hollow ring of mass 47,000 kg. The structures other than the ring shown in the figure have negligible mass compared to the ring. Members of the crew will walk on a deck formed by the inner surface of the outer cylindrical wall of the ring, with radius r = 150 m. The thickness of the ring is very small compared to the radius, so we can model the ring as a hoop. At rest when constructed, the ring is to be set rotating about its axis so that the people standing inside on this deck experience an effective free-fall acceleration equal to g. The rotation is achieved by firing two small rockets attached tangentially to opposite points on the rim of the ring. Your supervisor asks you to determine the following: (a) the time interval during which the rockets must be fired if each…
Trina is a gym goer with a leg length of 84 cm. Suppose that she is in the gym doing straight legraising with 10 lb weights. Compute for the force that the muscle should exert in order to (1) maintain it in the position and(2) lift the weight up given that the distance of the effort (muscle) from the joint is 54 cm,distance of the weight is 80 cm, and the COM is 45 cm from the joint. ANSWER THE QUESTION: 1.) Assuming that the leg moves at 0. 9 seconds, compute for the angular velocity. GIVEN: Leg length = 84 cm = 0.84 m Distance of the muscle from the joint = 54 cm = 0.54 m Distance of the weight = 80 cm = 0.80 m Distance of the COM from the joint = 45 cm = 0.45 m Mass = 10 lb = 4.535 kg Linear displacement x = 38.971 cm Or x = 0.389 m