You have to extract the organic solution three times using 15 ml portions of 3 M hydrochloric acid. What will be the sequence of your actions? 1st ste✔ Choose... 2nd ste 3rd ste 4th ste 5th ste 6th ste 7th step 8th step 9th step 10th step 11th step 12th step Place the dichloromethane layer back into separatory funnel and start the extraction with two portions of NaOH Drain the dichloromethane layer to the Erlenmeyer flask labeled "Neutral compound" Add second portion of 15 ml of HCI into separtory funnel and shake Place the dichloromethane layer back into separatory funnel Add dichloromethane solution and first 15 ml of HCI into separatory funnel and shake Add third portion of 15 ml of HCI into separtory funnel and shake Drain the aqueous layer to the Erlenmeyer flask labeled "HCI extract" Choose... Choose... Choose... Choose... Choose... Choose... → ◆ ◆ + ◆ +

You have to extract the organic solution three times using 15 ml portions of 3 M hydrochloric acid. What will be the sequence of your actions? 1st ste✔ Choose... 2nd ste 3rd ste 4th ste 5th ste 6th ste 7th step 8th step 9th step 10th step 11th step 12th step Place the dichloromethane layer back into separatory funnel and start the extraction with two portions of NaOH Drain the dichloromethane layer to the Erlenmeyer flask labeled "Neutral compound" Add second portion of 15 ml of HCI into separtory funnel and shake Place the dichloromethane layer back into separatory funnel Add dichloromethane solution and first 15 ml of HCI into separatory funnel and shake Add third portion of 15 ml of HCI into separtory funnel and shake Drain the aqueous layer to the Erlenmeyer flask labeled "HCI extract" Choose... Choose... Choose... Choose... Choose... Choose... → ◆ ◆ + ◆ +

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter5: Distillation

Section: Chapter Questions

Problem 11Q

See similar textbooks

Similar questions

Pcdotte Use a flow chart to show how you could separate a mixture of the following compounds using an extraction. Be sure to include all steps to get pure materials. НО.
Filter paper Saturated KNO; solution 259 Figure 1. Experimental apparatus. Experimental Procedure Part 1. Copper and Zinc Metal 1) Select a piece of copper and a piece of zinc metal wire from the containers in the hood. 2) Clean the surface of the metal wires with the steel wool. Wipe clean with a dry paper towel. 3) Obtain a plastic well plate. Fill one well with 10 drops of the Copper ion solution from the dropper bottle. Label this well with a Sharpie marker so that you remember which solution you filled it with, 4) Repeat step 3 with Zinc ion solution. Select a well right next to the well in step 3 so that the two wells with Copper and Zinc ion solution are right next to each other. 5) Obtain a small dry strip of filter paper. You may have to cut a large piece of filter paper down to the appropriate size. It should be exactly this big C It's OK to tear the filter paper with your hands. Using the drop bottle, saturate the filter paper strip with KNO; solution. Gently place one end…
1. Ph ОН Н Ill OH Me 0.1 equiv TSOH CHCl3, rt, 30 min 0.1 equiv TsOH CHCl3, reflux, 30 min
If 100 ml of a 1:1500 methylbenzethonium chloride lotion is diluted with an equal volume of water, what will be the ratio strength of this dilution? O a. 1:67 O b. 1:100 OC. 1:6000 O d. 1:3000 O e. 1:15000
Find the intermediates.show step-by-step solution.
Please solve the all problem with the full step thank u. Im needed ax in 30-60 minutes thank u A practitioner will make a titration curve. The practitioner pipetted 10 mL of 0.1 M HCl solution and put it into a clean and dry Erlenmeyer flask. After that, this practitioner prepared a clean burette (size 50 mL), mounted using clamps on a stand. The burette faucet was tightly closed, after being rinsed using 0.1 M NaOH solution. Using a funnel, 0.1 M NaOH solution was added to a scale of 0 mL. Place the Erlenmeyer flask containing the HCl solution just below the tip of the burette (under the faucet). Calculate the pH of the solution in the Erlenmeyer for each addition of a volume of 0.1 M NaOH solution. Make a table consisting of 3 columns (No, mL of NaOH solution added, calculation of the pH of the mixture). Fill in the mL of added NaOH solution ( 0, 1, 2, 3, 4, 5, 6, 7, 8, 9; 9.1; 9.2; 9.3; 9.4; 9.5; 9.6 ; 9,7; 9,8; 9,9; 10; 10,1; 10,2; .......etc . Draw a curve using millimeter block…
Submit a clean, dry, and properly labeled 50-mL reagent bottle for your unknown solution. Pipet 20.00 mL of the sample in 250-mL Erlenmeyer flask. Add 5 mL of buffer and 5 drops of indicator. Titrate the solution until it turns light blue. If the titration consumes more than 50 mL of the titrant, dilute the sample accordingly. Compute for ppm of CaCO3 using the following table. Mean Molarity = 2.487 x 10^-3 MBlank correction = 0.015 Formula = V (mL) titrant x Mean Molarity of Titrant x Molecular weight of CaCO3 x 1/V (L) sample
2 Trial 1: [4] Volume of NaOH, dispensed (mL) Trial 1: [5] Molar concentration of NaOH (mol/L) Trial 2: [4] Volume of NaOH, dispensed (mL) How Trial 2: [5] Molar concentration of NaOH (mol/L) Trial 3: [4] Volume of NaOH, dispensed (mL) Trial 3: [5] Molar concentration of NaOH (mol/L)
To which sample solution the spike will be add? the distillate>130C the mass standard the distilled <130C
Many operations in the chemical laboratory use “salting out” in the procedure. What do the purpose of this technique?
I want the solution very quickly within 15 minutes
0.02 M NaOH reagent was standardized using 0.1000 g Potassium hydrogen phthalate (204.22 g/mol) and it required 25.8 mL to reach end point.