Zy a o ZA Zy Zy The circuit shown is excited by a balance three phase source with a line voltage of Vab 347 V and -60° phase shift. If Z=2+j2 Q, Za = 12-j15 N, Ży=4+j6 Q, the average nOwer loss in transmission lines in kW is;

Zy a o ZA Zy Zy The circuit shown is excited by a balance three phase source with a line voltage of Vab 347 V and -60° phase shift. If Z=2+j2 Q, Za = 12-j15 N, Ży=4+j6 Q, the average nOwer loss in transmission lines in kW is;

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7MCQ

See similar textbooks

Related questions

Q: Q1: Lossless transmission line of 0.3 A having Z, = 50 2 terminated by load impedance of Z = 30 +j…

A: Here is your answer! I hope this will help you.

Q: Q5: (a) A lossless transmission line of I = 0.35 A of characteristic impedance 100 2, terminated by…

A: The solution can be achieved as follows.

Q: In a short transmission line, when the PF of the load changes from leading to lagging, the magnitude…

Q: A 150 2 lossless transmission line is connected to a load impedance ZL= 300-j300 2. Find the…

Q: 2. Estimate the distance over which a load of 12000 kW at a p.f. 0-65 lagging can be delivered by a…

A: First we will find current from power, power factor and voltage. Power losses=3×I2×total resistance…

Q: Consider the transmission line circuit shown in the accompanying figure. Compute the incident power,…

A: It is being given that : The length of the line : l=λ2 Generator Voltage : Vg=10 V Generator…

Q: A lossless transmission line of impedance Z : 100 + j75. If X=20 cm, find: 502 is terminated with a…

Q: 02: A lossless transmission line of electric length 1= 0.35 A is terminated in a load impedance as…

A: Given that: i=0.35π , Zin = 60+30n Find Bl =2ππ× 0.35π…

Q: A lossy transmission line of length 5 m has a characteristic impedance of (20 + j15)ohm. When the…

A: Given data Length is L = 5 m Characteristic impedance is Z0 = 20+j15 ohm Input impedance is Zin =…

Q: Q) A transmission line of length 0.40A has a characteristic impedance of 100 n and is terminated in…

Q: Q4: (Using Smith chart): A 100 2 transmission line connected to cellular phone antenna with load…

Q: A lossless transmission line is terminated with a 100 Ohms load (RL=100 Ohms). If the standing wave…

Q: The voltage waveform on a lossless TL in air is given by: /(z)=200e-jßz + 30e*JBZ (V). The TL has a…

A: v(z)=200-jBz+30ejBz voltzo=50Ω, l=2λfind TL,zL, vload

Q: A 100MHZ generator with V=1020° (V) and internal resistance 502 is connected to g lossless 502 air…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: a) Certain measurements made at 5 kHz on a half kilometer long transmission line. The results show…

A: Given, length of transmission line, l = 0.5 km Frequency, f = 5kHz Characteristic impedance, zo=…

Q: Each transmission line of the 3 wire, three phase system in Figure has an impedance of 15 ? +j 20 ?…

Q: Load impedance 30 + j10(N)is connected to the lossless transmission line 0.101 A and characteristic…

A: Load impedance 30+j10 Ω is connected to the lossless transmission line 0.101 λ and characteristic…

Q: Given a telephone T.L 100 miles long with Zo = 685-j92 N , a = 0.00497 Np/mile and B = 0.0352…

Q: The impedance of the 500 km long transmission line is Z = 0.1 + j * 0.4 ohm / km. At the end of the…

A: Given data, Ir=988.1 ∠-68.6°Vr=400 kVZ=50+j200 Ω By using short transmission line equations,…

Q: 5. (a) A transmission line of characteristic impedance Zo = 50 2 is to be matched to a load…

Q: a) Assume the line is lossless b) Assume the line has a small loss equivalent to R’ = 1.2 Ω/m

A: Concept: A capacity to do work is called energy and it may exist in potential, kinetic, thermal,…

Q: A 500-kV 60-Hz three phase transmission line is 463 km long. The series impedance is z=0.06+j0.4 Q…

Q: Question.2(b):A transmission line has a characteristic impedance of 80 ohms and a parallel…

A: In this question we need to find a series Inductance of the transmission line.

Q: In the transmission-line circuit shown below all lines are lossless, 2Z01 = Z02 = 1002 and RL1 R12 =…

A: Given Z01=Z02=100 ΩRL1 =RL2=50 Ω Lossless line

Q: Terminated transmission line. A 502, 10.5-m long air transmission line terminated with a load…

Q: B. A transmission line is loaded with a short circuit (ZL= 0). Prove that the line impedance can be…

Q: Consider a transmission line of characteristic impedance 50 ohms. Let it be terminated at one end by…

Q: A lossless 51-N transmission line is terminated in a load with Z = (42 + j29) N. Use the Smith chart…

A: Given Zo = 51 ohm ZL= 42+j29 ohm

Q: / Given a telephone T.L 100 miles long with Z,= 685 - j92 Q, a = 0.00497 Np/mile and B = 0.0352…

A: According to the question find the sending end impedance, voltage, current and power with the help.…

Q: 25: (a) A lossless transmission line of I = 0.35 2 of characteristic impedance 100 2, terminated by…

A: As per Bartleby guidelines we are allowed to solve only one question with maximum three subparts,…

Q: [Q8] A loss-less 752 line is terminated on a load with impedance, (100+j150)Q. determine the…

A: A loss-less 75 Ω is terminated on a load with impedance 100+j150 Ω. We need to determine the…

Q: 21. For a lossless transmission line, determine the value of the input impedance given: ZL = 25…

A: Dear,as per company guidelines we can answer only one question at a time, kindly post other question…

Q: A transmission line terminates in two branches each of length 2/4 as shown. The branches are…

A: The power system consists of power generation, transmission, and distribution. The transmission…

Q: A lossless transmission line (TL) has a characteristic impedance of Zo= 250 N, a lo impedance of ZR…

A: "According to Company's policy we can answer only the first three sub-parts of a question, if you…

Q: In the system given below, transmission line impedances are Z1=(25+j5) Ω, Z2=(75+j15) Ω, Z3=…

A: In the system given below, transmission line impedances Z1=(25+j5) Ω, Z2=(75+j15) Ω, Z3= (100+j20)…

Q: A 3-phase, 208V system supplies a delta load with impedances ZAB = 150 235°, ZBC %3D - 12Ω /20ο and…

A: In this question, Three phase Delta unbalanced impedance is given. Find the line currents, active…

Q: What is the maximum impedance in a 25 ohm transmission line terminated by a load impedance of ZL=…

A: Given that, Z = 25 ohms and ZL = 12.5 + j50 ohms

Q: 21. For a lossless transmission line, determine the value of the input impedance given: ZL = 25…

A: Dear,as per company guidelines we can answer only one question at a time, kindly post other question…

Q: The 50 ohm transmission line isterminated with an unknown load. The magnitude of the reflection…

A: Transmission line

Q: On a distortionless line, the voltage wave is given by V(e') = 120e0025e cos(10°t + 20') +…

A: The given wave signal is combination of the incident and reflected wave. The first term is incident…

Q: Question.2(b):A transmission line has a characteristic impedance of 70 ohms and a parallel…

A: A transmission line is said to be lossless if and only if R = 0 G= 0 The characteristic…

Q: A lossless transmission line ofl = 0.35 A of characteristic impedance 100 2, terminated bv input…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.…

Q: Question.2(b):A transmission line has a characteristic impedance of 40 ohms and a parallel…

Q: 3.2 A distribution line has an impedance of Z = 6.73+j4.87 N. The receiving-end line-to-line voltage…

A: Regulation of transmission line: Voltage regulation of a transmission line is the rise in…

Q: solve completely The internal resistance of the generator connected to the input of a transmission…

Q: Coaxial cable of an infinite produces reflection coefficient of – 0.3 + j0.4 when terminated in a…

A: Given: Coaxial cable of an infinite produces reflection coefficient of (-0.3+j0.4) when terminated…

Q: A load impedance ZL = (45 - j60)2 is connected to a line that has a characteristic impedance 75Q. By…

Q: A lossless 50 Q transmission line has an electric length of L=3/8. It is connected to a generator…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: The load impedance can be adjusted to the transmission line in accordance with the figure by using a…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Focus whether it's rms or not

Zy
ZA
Zy
Zy
The circuit shown is excited by a balance three phase source with a line voltage of Vab-
347 V and -60° phase shift. If Z=2+j2 Q, Za = 12-j15 Q, Ży = 4+j6 Q, the average
power loss in transmission lines in kW is;

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Two SGs are supplying a load by Pwad with 0.9 PF lagging. Gi has a no-load frequency of 54H2, and a slope Spi=1.1MW/Hz. G2 has a no-load frequency of 51HZ, and a slope Spz=1.1MW/Hz. If the system frequency is 50HZ: 1. How much power is supplied by each generator? 2. What is the load power Pload? 3. Draw the house-diagram for this system. 4. Find the system frequency, if the governor set points on G1 are decreased by 1Hz.
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
Consider the system in the figure to the right. The Zbus for the system is given as follows: [j0.411 j0.310 j0.3541 Zbusj0.310 j0.446 j0.333 Lj0.354 j0.333 j0.450] j0.8 1.28/0 ele j0.2 vor j2.0 j0.5 m j0.4 m 2 a) Find the voltage at each bus. b) Find the current drawn by a capacitor having a reactance of 5.0 PU connected from bus 3 to the reference. c) Find the change in voltage at each bus when the capacitor is connected at bus 3. d) Find the voltage at each bus after connecting the capacitor. j1.0 1.20/30°
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
An inductive circuit draws a line current of 10A. If the reactive component of the line current is 6A, then power factor of the circuit is ___ . a. 0.6 lagging b. 0.857 lagging c. 0.5 lagging d. 0.5 leading
CAN YOU EXPLAIN THE OPERATIONS IN SENTENCES? For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ?
7. For the circuit below, calculate the value of Z₂ for maximum average power transfer to the load. In addition, determine the value of the maximum average power absorbed. (Hint: One approach is to find the open-circuit voltage and the short-circuit current.) j4 2 Vx -j2 n 16 Vx20 4/0° V ZL
A synchronous generator may be represented by a voltage source of magnitude 1.7 p.u. in series with an impedance of 2 p.u. It is connected to a zero-impedance voltage source of 1 p.u. The ratio of X/R of the impedance is 10. Calculate the power generated and the power delivered to the voltage source if the angle between the voltage sources is 30°.
Estimate the distance over which a load of 15000 KW at p.f-0.8 lagging can be delivered by a 3-phase T.L having conductor each of resistance 0.8 2 per km the voltage at the receiving end is to be 132 KV and the losses in the line is to be 5% of received power
The total power drawn by the two-impedance load in parallel is 26kW at 0.98 power factor lagging, it is being supplied by a 230-volts AC source. One of the loads (Load 1) takes 16kVA at 0.77 power factor lagging. What is the reactive power of the unknown impedance (Load 2)?