1.) The truss shown is made of steel members ( E = 29 x 106 psi ). Members AB and BC have cross-sectional areas of 0.80 in² and 0.64 in? respectively. For the loading shown, determine the elongation ofboth membersBA25 kips5A KipsFigure #1

consider the equilibrium of joint A∑FH=0,in ∆ABD,tanθ=56therefore,sinθ=551 and…

1.) The truss shown is made of steel members ( E = 29 x 106 psi ). Members AB and BC have cross- sectional areas of 0.80 in? and 0.64 in2 respectively. For the loading shown, determine the elongation of both members B E Figure #1 25 kips 54 Kips

1.) The truss shown is made of steel members ( E = 29 x 106 psi ). Members AB and BC have cross- sectional areas of 0.80 in? and 0.64 in2 respectively. For the loading shown, determine the elongation of both members B E Figure #1 25 kips 54 Kips

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The truss ABC is constructed of three titanium (E Ti =17.4×10 3 ksi) members. A horizontal force of 1.8 kip and an unknown force P are applied to the truss at point B as shown. Member AB has a cross-sectional area of 0.1in 2 , member BC has a cross-sectional area of 0.0025ft 2 , and member AC has a cross-sectional area of 0.2 in2. b) Determine the magnitude of the force P that is required to displace the roller at point C to the right by .03 inches.
The truss shown in the figure is applied with force P= 5kN %3D 1.50 m 1.50 m 150 m 2 m 2 m What is the force in member DE in kN? A.
2.54 The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3. What is the length of the gap A? The cross-sectional areas are 300 mm? for rod AC and 250 mm² for rod BD. Use E = 200 GPa for steel. A B 0.75 m -1.5 m 2 m FIG. P2.53, P2.54
Determine the magnitude and direction of Ra, Rb and Rc for the truss shown in the figure.
In the figure shown, the Aluminum member (AC) with a diameter of 1.125in is connected with the steel member (CD) of a diameter of 1.625in from point C, these members are restrained by rigid supports at A and D. Find: 1) The values of reactions at supports A + and D 2) The deformation at point C () E = 10.4 x 10°psi E = 29 x 10 psi 1SKips 14Kips A C 8 in 10 in 10 in
3. For the truss shown in the figure for this question, members AB and CD shown in bold each have a weight of 2 N. 4 m IC Establish the force in members BC, E I 3. CG, DE, and GH. Ans. FBC = 8 N (tension) FCG = 1.67 N (compression) FDE = 0 FGH = 6.67 N (compression) %3D 5 N 2N 7 N %3D %3D
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross sectional area of 500 mm^2. Link CD made of steel (E = 200 GPa) and has a cross sectional area of 600 mm^2. Determine the deflection at D in mm
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 619 mm?. For the 41 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places 04 m 0.3 m E 0.4 m 0.2 m
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in2 for all the members. Determine the deformation sustained by members CG and FG
Zero-Force Members are structural members that support No loading but aid in the stability of the truss. Tips on getting the zero-force members: 1. there is no external load or reaction at that joint 2. Insufficient structural members to satisfy or "balance" the system: Summation of forces along the horizontal and vertical 3. two of the members are collinear As shown in the figure, structural members of zero-force members can be noticed through observation. H G F A D E At a glance, it can be inferred that the member FG and FE are zero force members, because: First, there is no external load applied on the joint Secondly, taking the Joint F, if Summation of Forces along horizontal = 0 is executed, only the member FG has the horizontal component, or the "ability" to "balance" the system, and if Summation of Forces = 0 is executed, the member FE has the vertical component, or the "ability" to "balance" the system only. along vertical Aside from members FG and FE, through observation,…
Determine the force on the EF and EG elements on the truss shown in the figure and consider P = 35kN. Final answer: EF force = 69.5kN T Force at EG = 250kN C
Zero-Force Members are structural members that support No loading but aid in the stability of the truss. Tips on getting the zero-force members: 1. there is no external load or reaction at that joint 2. Insufficient structural members to satisfy or "balance" the system: Summation of forces along the horizontal and vertical 3. two of the members are collinear As shown in the figure, structural members of zero-force members can be noticed through observation. Load P Н, G F A D E At a glance, it can be inferred that the member FG and FE are zero force members, because: First, there is no external load applied on the joint Secondly, taking the Joint F, if Summation of Forces along horizontal = 0 is executed, only the member FG has the horizontal component, or the "ability" to "balance" the system, and if Summation of Forces = 0 is executed, the member FE has the vertical component, or the "ability" to "balance" the system only. along vertical Aside from members FG and FE, through…