4.2. A thermometer having a time constant of 1 min is initially at 50°C. It is immersed in a bath maintained at 100°C at t = 0. Determine the temperature reading at t=1.2 min.
Q: Please answer all subparts please answer in typing format
A: Step 1: Step 2: Step 3: Step 4:
Q: In an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz,…
A: Step 1:Step 2:
Q: Solve e) and f) only showing all the steps in your work peoperly.The figure is attached
A:
Q: only a, b, c and d please
A:
Q: Design an oscillator with an amplifier with gain of 12 and phase angle of 192 degrees. The feedback…
A: The objective of the question is to find the phase shift of each phase shifter in an oscillator…
Q: Q3: In a communication system, the message given by m(t) = cos(20πt) frequency modulates the carrier…
A: The question asks for calculations and sketching related to a frequency modulation (FM)…
Q: Please answer in typing format
A: Given: RMS voltage (V_RMS) = 381 VModulation index (m) = 0.9Switching frequency (f_s) = 5 kHz = 5000…
Q: 3.23. Determine the stability for each of the following linear systems. a. y(n) b. y(n) = == Σk=0…
A: to determine the stability of two linear systems described by their respective equations: a.…
Q: : It is required to obtain the bus voltages for the power system shown in Fig. (3) by applying…
A: Here are the steps to solve the problem for bus 2:Build the bus admittance matrix (Y bus): This step…
Q: Please answer in typing format
A: To solve for the output voltage Vo in the given circuit, we need to apply the fundamental laws of…
Q: I need the complete solution.
A: Step 1: Step 2: Step 3: Step 4:
Q: Q2: The constants of a 275 KV transmission line are A = 0.8525° and B = 200275° 0/phase. Draw the…
A: the power and power angle at unity power factor that can be received at the receiving end of a 275…
Q: Please answer in typing format
A: KIRCHHOFFS CURRENT LAW: It states that the algebraic sum of currents entering into the node is…
Q: Please answer in typing format
A: The information provided is not sufficient to definitively determine the value of TC. Here's why:…
Q: Q/A discrete system described by the following difference equation y(n) = x(n) 0.9 x(n - 1) - 0.1…
A: Step 1: Step 2: Step 3: Step 4:
Q: 7.3 The voltage and current of an electric load can be expressed by the following equations: v340…
A:
Q: I need help checking if my answer is correct 1) Using superposition, determine the current through…
A:
Q: Please don't use matlab please answer in typing format
A: Output:0: zerosx: poleslocus(diamond):s = 1.24s = -7.24
Q: D 15.46 Design the circuit in Fig. 15.24(a) to obtain symmetrical triangular and square waveforms of…
A: The frequency of the waveform is given as 10 kHz. The frequency of a triangular waveform is given by…
Q: 03: Given the sequence x(n) = [0.8, 0.6, 0.4, 0.2]. a) Compute its spectrum using DFT X(k). b)…
A: Step 1: Step 2: Step 3: Step 4:
Q: Please answer in typing format
A: Step 1: Step 2: Step 3: Step 4:
Q: QUESTION ONE a) Determine the electric force (F), electric field (E), electric flux, electric flux…
A: Step 1: Step 2: Step 3: Step 4:
Q: Please solve this exam style question clearly and short. Answer correctly
A: Step 1: A 1-bit CMOS static RAM cell typically consists of two cross-coupled inverters (latches) to…
Q: Problem 2. A joint probability mass function of X and Y is given in the following table. Find the…
A: Step 1:Given joint mass function of X and Y is : X…
Q: With examples, make out difference between (a) min term & max term (b) positive and negative…
A: In Boolean algebra, a min term is a product of variables, where each variable is either in its…
Q: Can you check if the Zth that I got is correct The Zth I got was: Zth = 754.88 + j628.32 Zth =…
A:
Q: Two sections of an electric railway are supplied by a Scott transformer. The following figure gives…
A: Step 1:Step 2:Step 3:
Q: I didn't understand the method of solving this question. I don't need a detailed explanation; I just…
A: Step 1: Step 2:
Q: Q armnul nower factor VIS Curren Q3) Design a Three phase to single phase step down cycloconverter…
A: Solution: Designing a three-phase to single-phase step-down cyclo converter using two three-phase…
Q: Please answer the below question explaining each step Solve using nodal analysis (preferably) and…
A: Your mistake was that you mixed up 2 superposition nodal equations, that are supposedly must be…
Q: 4) Consider the following circuit. a) find the frequency and the phase angle of the source. b) find…
A: Step 1:Step 2:Step 3:
Q: Please answer in typing format
A: 1)Solving the equation with k-mapAs u can see for the powers of 2 orderu can see that2 corners i.e 4…
Q: A circuit designed to fire a laser flash tube consists of the following (see fig below): a 12 V…
A:
Q: Please answer in typing format for
A: To find the amplitude, frequency, phase angle, and phasor V of the sinusoid v(t)=6cos(5t+17):…
Q: 3-phase-demos-3vi File Edit View Project Operate Tools Window Help Waveform Chart 8 21 2- 18- 16-…
A: Step 1: When all the diodes were connected, each diode is responsible for 3 pulses of 120 degree in…
Q: Please answer in typing format
A: Step 1: Before changeover of switch, the capacitor was fully charged to 100V from dc source and…
Q: Al-Iraqia Universirty Electric Engineering Department Control Theory Dr. Ayad Mahmood Kwad لجامعة…
A: Step 1: Step 2: Step 3: Step 4:
Q: 4. A. Find Ic and VCE in the circuit below if T-25°C and if hFE=200. B. Using the hybrid-pi model,…
A:
Q: Determine the differential equation that describes the LT-I system having the following Frequency…
A:
Q: For the FET amplifier shown in fig(1), given FET parameters gm=4000us, and ra-100k. (1) What is the…
A: the current through resistor R_2 (10 Ω) and the voltage across resistor R_3 (40 Ω). However, due to…
Q: • Find Current R1 and R2 And find the voltage in R3 Apply 3. Thevenins theoram
A:
Q: Q1) For the circuit shown in Fig (1). (a) Draw the output voltage and load current waveforms if the…
A: Q1)1. Whenever IGBT pairs are conducting, the voltage and current have the same polarity thereby…
Q: Y(s) 3.17 다음의 신호 흐름도에서 전달함수 T(8) = 를 구하라. R(s) b₁ K₁ 1 LS7 R(s) o -a1 a2 LS 1 br Y(s)
A:
Q: Consider the mobile communication system shown in Figure 2. Assume the tower is providing mobile…
A: Step 1: Step 2: Step 3: Step 4:
Q: The parameters of a certain transmission line operating at w = 6 x 10° rad/s are L = 0.350 µH/m,…
A: Given data:ω = 6×108 rad/sL = 0.350 µH/mC = 40 pF/mγ = 0.094 + j2.25 m-1 As we know the propagation…
Q: 11.5 Three single-phase transformers, each is rated at 10 kVA, 400/300 V are connected as wye-delta…
A:
Q: Using Nodal Analysis, determine the voltages at nodes (1, 2 and 3) of the circuit shown in Figure…
A: Step 1: Step 2: Step 3: Step 4:
Q: I need help checking if my answer is correct 1) Using superposition, determine the current through…
A: Step 1: Step 2: Step 3: Step 4:
Q: #4. Calculate the rms value for each of the following functions: (a) i(t) = 10 A (b) v(t) = 4 + 3…
A: Step 1:To calculate the root mean square (rms) value for each of the given functions, we'll use the…
Q: Use the following for all 3 circuits. V1 = 9.0 V, V₂ = 12.0 V R₁ = 2.0 ohms, R₂ = 4.0 ohms, R3 = 6.0…
A:
Step by step
Solved in 2 steps
- 11:03 b C Pmark question If the forward voltage drop on a diode is 774 mV, what is the current passing through it? Assume I s =3,4x10-16 A. If the forward voltage drop across a diode is 774 mV, what is the current flowing through it? Is =3.4x10 Get an A. -16 ( a. 2,885 mA b. 4,327 mA c. 3,606 mA D. 2,163 mA O to. 5,048 mA { * . . 51% - Previous page ||| Next page ← Announcements - Teams code: fmf9zv7 <2.3 A thermocouple element when taken from a liquid at 50°C and plunged into a liquid at 100°C at time t-0 gave the following e.m.f. values. Determine the 95% response time. Time (s) e.m.f. (mV) 2.5 20 40 60 80 100 120 3.8 4.5 4.8 4.9 5.0 5.0The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 1 V/cm. Determine the (i) amplitude of waveform Q (i) peak to peak value of waveform P. (ii)i frquency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. () Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (ii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =
- 8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35An iron ring elecromagnet has a relative permeability of 1250 when it is excited by a coil having 500 turns at 0.8 A. the mean length of iron parts is 48 cm, the cross-section of the core is 10 square cm and the air gap is 0.5 cm. What is its total reluctance?Why is it desirable to wait 1 s after a potential pulse before recording the current in voltammetry?
- The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (ii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 30 V/cm. Determine the (1) amplitude of waveform Q, (i) peak to peak value of waveform P, (ii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =The wavelorm displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 50 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (1) amplitude of waveform Q, (ii) peak to peak value of waveform P, (111) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. 主 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P (iii) Frequency of waveform P =
- How does the internal resistance of the multimeter (in voltage setting) affect the charging/discharging rate of the capacitor. Explain.V₁ 12 In the figure shown, what is the peak to peak voltage of V1 if the vertical sensitivity of the oscilloscope is 0.25 V/Div* HIPNHHHH ALLBriefly in your own understanding explain attenuation in electrical engineering.