EXERCISE 3The aluminum rod BC (G = 26 GPa) is bonded to thebrass rod AB (G = 39 GPa). Knowing that each rod issolid and has a diameter of 12 mm, determine the200 minBrassangle of twist(a) between A and B.Ans AR: 14.43•Aluminum(b) between B and C,Ans PBc: 32.47•300 mm(c) At CAns Pc: 46.90•100 N- m

Answered: Image /qna-images/answer/8defb40b-3c9a-4d46-b63b-6cd2eaab7f9a.jpg

Answered: angle of twist (a) between A and B, (b)…

Engineering

Mechanical Engineering

angle of twist (a) between A and B, (b) between B and C, um (c) At C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2 kN-m 40 mm 50 mm Bronze Steel dia. dia. B 400 600 mm mm Composite shaft ABC is fixed at A as shown. The steel member ABC has an outer diameter of 50mm. It is hollow at segment AB, with a 40mm inner diameter and is solid at segment BC. At the hollow segment AB, a 40mm diameter bronze rod is fully bonded with the steel encasement. The modulus of rigidity of steel and bronze are 75GPA and 38GPa, respectively. A 2KNM torque with direction as shown is applied at point B. 1. Determine the internal torques carried by the steel tube and the bronze rod at segment AB. 2. Determine the maximum and minimum shear stresses in the bronze rod within segment AB. 3. Þetermine the angle of rotation of section C with respect to the fixed support. Express your answer in degrees
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa
QUESTION 4: [Torsion of Circular Shafts] 1. The aluminium rod ABis bonded to the brass rod BD. Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. Take GAI = 27 GPa and Gpr = 39 GPa respectively. 60 mm T- 1600 N - m 36 mm T- S00 N. m 250 mm 375 mim 400 mm
The shaft, shown below, consists of rods AB and CD and a tubular segment BC. The rods are connected with the tubular segment using bolts at B and C. If a torque T is applied to the shaft, determine: a) the number of bolts required for the connection at B or C. Use 15 mm-diameter bolts with Tallow=50 MPa. The bolts are located at a radial distance p measured from the longitudinal axis of the shaft. b) The diameter of the solid rods AB and CD. Given that the allowable stress for the shaft is Tallow=140 MPa. T (kN.m) p (m) 27 0.4 O (Ctrl) B т
1. The shaft assembly shown below is fixed at its ends A and D. It consists of an aluminum (G = 30 GPa) segment AB rigidly connected to a steel (G= 75 GPa) segment BCD. Both segments have a 80-mm diameter. If the shaft is subjected to a torque 7 of 9 kN-m applied at C, determine The reactions at A and D; a) b) The angle of twist at point B; The maximum shear stress in the shaft. 300 mm -Aluminum 600 mm Steel C 300 mm
E' 3. For the 3-in.-diameter solid cylinder and loading shown, T = 40 kip-in., determine: (a) the polar moment of inertia, (b) the maximum shearing stress, (c) the maximum shearing strain, and (d) the angle of twist d. Use G=77 GPa for the modulus of rigidity and the length of the rod as 10 ft. 3 in.
A constant torque of 75 lb-in. is applied to the circular rod below, with a radius of 2 in. The shear modulus G = 3.5 x 106 psi. What is the angle of twist, p, at the end of the 6 foot long rod? 0.117 rad 0.056 rad 0.234 rad 0.314 rad T
200 mm Q2) The aluminum rod BC (G-26 GPa) is bonded to the brass rod AB (G-39 GPa). Knowing that irass cach rod is solid and has a diameter of 12 mm, 300 Alamuinm determine the angle of twist (a) at B, (b) at C. Then find the maximum stress in the Brass and Aluminum bars. 100 N
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
1. The aluminium rod AB is bonded to the brass rod BD. Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. Take GAL = 27 GPa and Gay = 39 GPa respectively. 60 mm T- 1600 N- m 36 mm T- S00 N. m 250 mm 375 mm 400 mm Figure Q4.1: Compound shaft
A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in the samedirection. Segment AB is 4 m long, BC is 2 m long, and CD is 4 m long. Supports A and D are fixed and unyielding.G = 86 GPa. Determine the ff:A.) Reaction at A (N-m)B.) At what segment is the torsional stress largest? What is the stress on that segment? (MPa)C.) Angle of rotation between points A and C (radians)
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.