Copy the sketch of the tensile stress-strain test (Figure A1) results for a waisted metallic specimen and indicate the locations representing maximum stress (A), ultimate strain to failure (B), and 0.2% proof (yield) stress (C), and calculate the Young's modulus of the material. 300 250 200 150 100 50 0 Stress (MPa) 0.2 0.4 0.6 Strain (%) 8.0 10.0

Copy the sketch of the tensile stress-strain test (Figure A1) results for a waisted metallic specimen and indicate the locations representing maximum stress (A), ultimate strain to failure (B), and 0.2% proof (yield) stress (C), and calculate the Young's modulus of the material. 300 250 200 150 100 50 0 Stress (MPa) 0.2 0.4 0.6 Strain (%) 8.0 10.0

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured on l. 16 cm gauge length were determined as follows: B A B C Load (kgf) 4800 8400 7200 Elongation (mm) 0.192 28.8 38.4 c) Calculate the fracture work and the maximum elastic energy the metal rod can store. d) Find the cross-sectional area of a 6 m long rod made of this metal such that it can carry 12 tons of load with 2 times the safety of yield strength. How long does the rod extend under this load?
A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2% offset is 6800 kg, the yield stress will be nearly 1. 31 kg/mm² 2. 43 kg/mm² 3. 51 kg/mm² 4. 63 kg/mm² X
Calculate the stress from a 0.3498 in. diameter tensile specimen yielding at 4.407 kips 46.0 ksi 30.6 ksi 33.4 ksi 45.9 ksi
During a tension test, measurements for the applied load and the corresponding elongation are taken at frequent intervals. These data points are then used to: a. calculate the stress caused by the applied load at each data point. b. calculate the strain in the specimen induced by the applied load at each data point. c. plot a stress-strain diagram. d. all of the above
An applied torque results in a shear strain (y) of 3.75 x 103 in a solid circular steel shaft. At this strain, a portion of the shaft cross- section yields as shown in Figure 2. Determine the magnitude of the applied torque. Take G = 80 GPa and yy = 2.8125 x %3D 10-3 FIGURE 2: Plastic zone 50 mm 200 mm Elastic core
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P = 30 kN. Knowing that E = 70 GPa, and the change in diameter of the rod= 0.00955 mm, determine the poissons' ratio v. -20-mm diameter gage length=150 mm
An aluminium specimen with an initial gauge diameter d, = 10 mm and gauge length, 1, = 100 mm is %3D subjected to tension test. A tensile force P= 50 kN is applied at the ends of the specimen as shown, resulting in an elongation of 1 mm in gauge length. The Poisson's ratio (µ) of the specimen is Take shear modulus of material, G = 25 GPa. Consider engineering stress-strain conditions. P
Sketch the stress-strain curve of the following tension test??? In the tension test of a metal fracture occurs at maximum load. The conditions at fracture were: A = 100 mm and L, = 60 mm, the initial values were: A = 150 mm and L. 40 mm.
A)Define poison's ratio B)A tensile-test piece of diameter 10mm is subjected to an axial force of 15KN.If E for the material is 207KN/mm^2 and poison's ratio is 0.29, calculate the lateral strain and the change in diameter.
The following observations were made during a tensile test on a mild steel specimen 40 mm in diameter and 200 mm long. Elongation with 40 KN load (within limit of proportionality) Change in length=0.0202 mm. Determine stress and strain value
A tension test is being conducted on a steel-rod specimen with a gauge length of L0=2 in and initial diameter of d0=0.5 in. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 74.0 ksi, e = 104.0 ksi , g = 85.0 ksi , and h = 0.15 in/in. Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 2.7 in . Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 11.0 kips, find the nominal stress experienced by the rod. Determine the force P needed to reach the ultimate stress in the steel-rod specimen.