Solve part c only Three samples of Soil were collected during soil exploration for the constructionof a Highrise Building. a) Choose the most appropriate Test to determine shearstrength parameters for each of the sample described as underi) Saturated Plastic Clayb) Draw typical graph hetween shear stress and normal stress for each of theiI) Well Graded SandI) Silty Claysample described as above.c) Describe Mohar's theory of rupture

The Mohr Theory of rupture is based on the famous Mohr's circle. Mohr's theory is often used in…

Answered: Describe Mohar's theory of rupture

Engineering

Civil Engineering

Describe Mohar's theory of rupture

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter12: Shear Strength Of Soil

Section: Chapter Questions

Problem 12.18P

See similar textbooks

Related questions

Q: What is the crack pattern induced by hydration due to internal restraint?

A: When the temperature is rising, the inner concrete’s temperature is above outer concrete’s…

Q: Why is it necessary to limit the widths of cracks?

A: Cracks are of concern for three main reasons: Appearance Leakage of air or fluids through the…

Q: How local shear failure differs from general shear failure ?

A: General shear failure These above figure describe a strip footing resting on above the surface of a…

Q: 1.Dents in railway culverts, what type observed on floors? Explain

A: Railway culverts: Railway culverts are used to carry the watercourses under the long-term way (or)…

Q: what do columnar joint and mud-cracks have in common?

A: Like mud-cracks, columnar joints form from volume contraction. In the mud-cracks, volume decreases…

Q: How many types of cracks can occur in a building?

A: To find: Types of crack that can occur in building.

Q: Just give any idea about design of one way continuous slab problem given

A: As the question requires only idea to solve one way continuous design slabs. So it requires only…

Q: Explain the PRINCIPLES OF FOUNDATION ENGINEERING ?

A: The main objectives of foundation design are to ensure that the structural loads are transmitted to…

Q: Why do BS8007 specify the allowable crack width of water retaining structure as 0.2mm for severe or…

A: The self-sealing capacity of concrete - Self-healing capacity of concrete occurs when- On a cracked…

Q: Explain the difference between posthole auger and the helical auger ?

A: There are two kinds of hand auger as follows, Helical augur Post hole augur.

Q: What are the basic components of the reinforcing earth construction?

A: basic components of reinforcing earth construction are : 1- Soil 2- Reinforcement 3- Skin

Q: ny types of cracks can

A: Answer is option c There can be 2 types of crack in building

Q: Define the function of grout inside tendon ducts?

A: The mixture of cement, sand , chemicals and water which is used to fill the gap is called as grout.…

Q: Define the functions of grout inside tendon ducts?

A: The mixture of cement, water, and sand is called as grout. The grout is less stiffer compared to…

Q: 1. What are the mainly two types of failures occur in beams? Tension zone Load

A: The two main types of failures which occur in beams are: 1) Flexural failure 2) Shear failure 1)…

Q: The small (or short) crack problem : What is it? Why does it matter? (– and are modern NDT…

A: Cracks are very serious in the concrete structures and the same cracks in masonry define the…

Q: Describe the benefits of having foundation installations overseen by professionals who are…

A: Benefits of Having Foundation Installation overseen by professionals who are knowledgeable with the…

Q: What are the various grouting materials ?

A: The different types of grouting materials used in construction : Cement Grouting:As the cement have…

Q: Define The structural ultimate limit

A: In the limit state method a structure is designed for safety against collapse (for ultimate strength…

Q: Explain Procedures for bracing excavation sheeting..

A: Procedure of the Bracing Excavation:

Q: Describe about the Installation procedure of Excavation Bracing?

A: Deep excavations with vertical sides need lateral supports to prevent cave in of the soil and to…

Q: Explain under which situation shall engineers use jacking at one end only and from both ends in…

A: During Pre-stressing work at only one end, frictional losses will occur and the applied force…

Q: What is the required minimum thickness (mm) of a 5m long both-end continuous, one-way slab if its…

A: Span length, L= 5m Steel rebar yield strength, Fy= 420 MPA Both ends continuous

Q: Discuss the brief notes on : Mat foundation ?

A: Foundation A foundation is a structure which connects to the ground and foundation transfers the…

Q: Why are voids filled with lightweight infilling material in raft foundation ofpumping stations?

A: Answer:- Raft foundation: A raft footing is a footing that covers the entire area below a structure…

Q: What is a tension crack atop a slope, and what is its meaning in slope stability analysis. What…

A: Cracks that form on the top of a mass of soil, commonly near a retaining structure or even at the…

Q: Write down the other methods for control of frost heave?

A: The frost heave can be defined as it is an uphill swelling of soil due to the development of ice…

Q: Describe about the methods that are commonly used to prevent the occurrence of, or to offset the…

A: Frost heave caused by ice formation during freezing conditions is an upward swelling of the soil. It…

Q: What is field load test?

A: The field load check is a semi-direct way of calculating the allowable soil bearing pressure to…

Q: Describe Mohar’s theory of rupture

A: In general practice different materials are acted upon by different combination of stresses. As a…

Q: How can the unknown vibrations, impact, or accidental loadings occur?

A: Unknown vibrations include different types of vibration loads which can act on the building and the…

Q: What are the several simultaneously occurring conditions are required for the notorious frost heave…

A: - Frost heave is a phenomenon in which upward swelling or upliftment of soil or other surface…

Q: How the significance of effective stress and drainage during shearing can be explained?

A: Shear strength is the capacity to resist shear stress. If the value of shear stress on any plane or…

Q: Define angle of nip with neat sketch for a double roll crusher.

A: Roll Crushers are compressive kind crushers that produce a very narrow product particle sizes and…

Q: What is the design procedures to design a concrete pipe using Manning Equations ?

A: Step 1: First the design flow of concrete pipe is determined taking the consideration of maximum,…

Q: What are the Types of the Excavation Bracing?

A: Braced excavation is a technique in which a sheeting and bracing system laterally supports deep…

Q: 60. If the loss of prestress is excessive resulting in ten cracks, which method shc used?

Q: What is inelastic bending?

A: Inelastic behavior is possible in beams that are made of ductile materials, and as such can be…

Q: Describe about the Floating Foundations.

A: Floating foundations can be simply explained as those foundations which are constructed by…

Q: Which microscopic fracture mechanism is associated with river patterns, and why do they form?

A: When observed under scanning electron microscope (SEM) a brittle material gives river pattern of…

Q: What is lift slab construction? Which type of connections we make hard/soft? And why we use such…

A: The slabs are flat surfaces, which is generally horizontal surfaces such as floors, roofs and bridge…

Q: a. What are “Shake maps”? State the significance and explain how they are constructed.

A: Shake maps are the representation shaking which are produced in ground due to earthquake. It mainly…

Q: Q1/ Explain the test type, indenter type, major load a)95 HRC b) 105 HRG

A: Hardness represents the resistance of material surface to abrasion, scratching and cutting. There…

Q: Describe different types of failure of foundations with example?

A: Foundation- It is the sub-structural element that is in direct contact with the ground and it…

Q: What steps can people take to avoid landslide disasters? Whatis the purpose of the rock bolts shown…

A: The movement of rock, soil, or debris down a sloped area of terrain is known as a landslide. Rain,…

Q: Describe Plate-bearing tests.

A: The Plate Bearing Test is defined as an insitu load bearing test of soil which is used for…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

Solve part c only

Three samples of Soil were collected during soil exploration for the construction
of a Highrise Building. a) Choose the most appropriate Test to determine shear
strength parameters for each of the sample described as under
i) Saturated Plastic Clay
b) Draw typical graph hetween shear stress and normal stress for each of the
iI) Well Graded Sand
I) Silty Clay
sample described as above.
c) Describe Mohar's theory of rupture

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1- Describe Mohr's theory

VIEW

Step 2-Describe about the stresses in the Mohr's theory

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

please help me... If a soil sample tested in a direct shear box of 60 mm by 60 mm and the maximum readings for normal loads of 0.3, 0.5 and 1.0kN were 202, 265 and 511 kN, determine the strength parameters corresponding to effective stress. Please find: 1) UU test; Unconsolidated Untrained (Q-test or quick test) 2) CD test; Consolidated Drained ( S-test or slow test) 3) CU test; Consolidated Untrained (R-test) 4) UC test; Unconfined Compression (σ_3=0) Thank you..
Separate triaxial compression tests are wwwmmmmmmmmmm performed on identical soil samples. The soil is a saturated mixed soil . At failure, the respective minor and major principal stresses values are 20 kPa and 46 kPa for sample one and 40 kPa and 80 KPa for sample two. From these. data, determine the value for Ø and the cohesion intercept C on the Mohr's circle shear strength coordinate.
Separate triaxial compression tests are performed on identical soil samples. The soil is a saturated mixed soil. Both tests follow the procedure for consolidated–undrained conditions. At failure, the respective minor and major principal stress values are 20 kPa and 46 kPa for sample one and 40 kPa and 80 kPa for sample two. From these data, determine the value for fCU and the cohesion intercept c on the Mohr’s circle shear stress coordinate. (This problem can be solved graphically using the Mohr’s circle.)
Three samples of Soil were collected during soil exploration for the construction of a Highrise Building. a) Choose the most appropriate Test to determine shear strength parameters for each of the sample described as under i) Saturated Plastic Clay ii) Well Graded Sand iii) Silty Clay b) Draw typical graph between shear stress and normal stress for each of the sample described as above.
A normally consolidated soil was subjected to tri-axial test with the following data: cell pressure= 320 kPa; The specimen failed when the deviator stress is 460 kPa. Compute the shear stress in kPa on the failure plane. Include fbd.
24.A series of consolidated, undrained triaxial tests were carried out on specimens of asaturated clay under no backpressure. The test data at failure are summarized:Confiningpressure (kPa) Deviator stress(kPa) Pore waterpressure (kPa) 150 192 80300 341 154450 504 222 a. Draw the Mohr circles and find the cohesion and friction angles in terms of effectivestresses.b. Compute Skempton’s A- parameter at failure for all three specimens.c. Is the soil normally consolidated or over consolidated? Why?d. Another specimen of the same day that was consolidated under a cell pressure of 250 kPa wassubjected to a consolidated, drained tri axial test. What would be the deviator stress at failure?
Q: Soil samples have been collected from a virgin ground and sent to a NATA accredited laboratory to determine shear strength parameters. The laboratory conducted direct shear test using 100 mm X 100 mm samples and returned the following test result. Test no. 1 2 Normal stress (kPa) 100 200 Shear stress at failure (kPa) 125 165 For the given soil, determine minor principal stress when major principal stress is are 400 kPa.
A normally consolidated soil was subjected to tri-axial test with the following data: cell pressure= 320 kPa; The specimen failed when the deviator stress is 460 kPa. Compute the shear stress in kPa on the failure plane. Show diagram
If an unconfined compression test is performed on the same clayey soil as described in Problem 4 , what axial load can be expected at failure? problem 4: A cohesive soil sample is subjected to an unconfined compression test. The sample fails at a pressure of 3850 lb/ft2 [i.e., unconfined compressive strength lb/ft2]. Determine the soil’s cohesion.
In determining the effective stress parameters of a soil sample, which test is preferable, consolidated undrained test or consolidated drained test?
Q-4: Soil samples have been collected from a virgin ground and sent to a NATA accredited laboratory to determine shear strength parameters. The laboratory conducted direct shear test using 100 mm X 100 mm samples and returned the following test result. Test no. 1 2 Normal stress (kPa) 100 200 Shear stress at failure (kPa) 77.74 135.47 For the given soil, determine minor principal stress when major principal stress is are 450 kPa.
Following are possible testing to determine the shear strength of clay in the laboratory, please choose the correct and appropriate combination for lab testing. I. Direct shear test II. Unconfined Compressive Strength III. Vane Shear test IV. Standard Penetration Test V. Consolidated Isotropic Drained triaxial test VI. Dutch Cone penetrometer O All above O 1,1Il and II O 1,1II and VI O IV, V, VI