What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

Q: Why is it important for inventors to value IP at the ideation stage of development? O O to establish…

A: Creating IP helps in reducing risk and generating value for the product.  It also acts as a shield…

Q: Consider the function p(x) = x - 4x³ + 3x²+x- relative error at the end of the second iteration?…

A: The function is: f(x) = x4 - 4x3 + 3x2 + x - 1 Interval is given as [2 3]. It is required to…

Q: An insulation system is to be selected for a furnace wall at 1000-C using first a layer of mineral…

A: Given:Furnace wall temperature, Ts=1000oCThermal conductivity of wool block, kwool=130 mW/moC=0.130…

Q: A closed container filled with hot coffee as shown below is in a room whose air and walls are at…

A:

Q: In the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring…

A:

Q: 4. Draw the complete shear and bending moment diagrams. -2 m 15 kN. 20 kN m -1 m- -1 m- 10 kN/m -2…

A: Given,

Q: A rigid tank that contains 5.2 kg of N2 at 25°C and 550 kPa is connected to another rigid tank that…

A:

Q: 8-2. If the coefficient of static friction between the incline and the 200-lb crate is #, = 0.3,…

A:

Q: A major water main is an 18-in ductile iron pipe. Compute the Reynolds number if the pipe carries…

A:

Q: A ball is thrown so that the motion is defined by the equations x = 5t and y= 2 + 6t - 4.9t², where…

A:

Q: At what distance, "a" should the bearing supports at A and B be placed so that the displacement at…

A: Given data: EI is constant

Q: In a detergent making process, 5.3 m³/h of water flows through a 50 mm pipe system as follows: Exit…

A: Following data is provided Flow rate of water Q= 5.3 m3/h Diameter of pipe (d) = 50mm  To find a)…

Q: Please write neatly and show all work and explanation So first Draw the free body diagram Then…

A:

Q: A thin 2 ft long rod weighing 10 lb is pinned at its end and balanced in a vertical position at A.…

A:

Q: 5 m 4m cg L... + B 2 m 3m GIVEN: BEAM MASS=45KG CENTER GRAVITY AT CG BOX MASS IS 90KG A = PIN B =…

A:

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A:

Q: Problem 2: A catastrophic failure occurred to a 7079-T6 aluminum alloy shaft. The maximum tensile…

A: Solution: Given Data: σmax,spec=0.3σy=0.3×300 MPa=90 MPaR=σminσmax=0a=2 cmc=1.3×10-4 cm   To Find:…

Q: During the Rayleigh process if the flow is supersonic, due to heat addition the velocity

A:

Q: 4/3- Methods of Joints/ Méthode des Nœuds Sample Problem / Exemple (4-1) Compute the force in each…

A: To find: The forces acting on each member using method of joints. Given: The diagram of truss and…

Q: During a performance test of an insulation wall, a 2 m longx3-m wide portion of the wall is placed…

A:

Q: Draw the shear-force and bending-moment diagrams for the cantilever beam shown. Determine the…

A:

Q: Same situation as the previous problem. Which expression is a correct application of summing the…

A: "Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Gas HAS CONSTANT MASS IDEAL GAS SPECIFIC HEAT RATIO OF GAS GAS CYCLE P↑ 29 At 1 At 2: At 3: ASK: A)…

A:

Q: Refrigerant 134a is the working fluid in an ideal vapor-compression refrigeration cycle operating at…

A: Given data: Refrigerant : 134a  Cycle : Ideal Vapor Compression cycle Conditions at compressor entry…

Q: (B) For a solid steel shaft shown (G-77GPa). It is failure by applying Torsion test. Determine: .…

A:

Q: Problem 13.056 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part…

A:

Q: A hot gas at 300°C with convective heat transfer coefficient of 100 W/m²-K is flowing through an…

A: Given:Hot gas temperature, Tg=300oCConvective heat transfer coefficient of hot gas, hg=100…

Q: Draw the complete shear and bending moment diagrams. A 1 m. 600 N 2 m 600 N -1 m- B

A: To find: Shear force and bending moment diagram for the beam.

Q: A 5 kg block is attached to a spring of constant k = 2400 N/m. The coefficient of friction between…

A:

Q: 3m 2 m 2m 1.5 kPa B D

A:

Q: The specific heat of copper is 0.093 cal/(g.°C) and the specific heat of gold is 0.031 cal/(g.°C).…

A: Given that: Specific heat of copper is 0.093 cal/(g.°C) Specific heat of gold is 0.031 cal/(g.°C)…

Q: We want to lower a suspended load in a controlled way, so that it hits the ground with a speed whose…

A:

Q: 11. Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW…

A:

Q: Estimate the aspect ratio (AR) for the F86 aircraft. 1.3 2.7 5.3 10.7 40 deg 3.0 m O 1.5 m 6.0 m

A: Write the given data. b1=1.5 mb2=3 md=6 mθ=40°

Q: 5. An air-to-air recovery unit uses a cross-flow heat exchange with both fluids unmixed and an air…

A:

Q: Problem 8.2

A:

Q: Q.5) Water (u= 1cP) is required to flow through a horizontal smooth steel pipe so that it discharges…

A: Assume flow through pipe is Laminar flow.

Q: Determine the minimum force P that can be applied without causing movement of the 250-lb crate which…

A:

Q: What's the correlation coefficient of the following data set? x = Type your answer... [-3 3 4 2 -1 1…

A:

Q: 5-97 A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa…

A:

Q: The minimum specific energy in a rectangular channel, 3-m wide, is 2 m. What is the discharge, in…

A: At minimum specific energy , depth of flow is critical and maximum discharge occurs..

Q: Problem 2: A U-tube manometer is connected to pressurized tanks (Tanks A and B), as shown in Fig. 2.…

A:

Q: The velocity of a particle which moves along the s-axis is given by s = 55-7t² m/s where t is in…

A: Given: velocity of the particle, s˙=55-7t2

Q: Consider the function p(x) = 24 - 4x³+3x²+x-1. Use Newton-Raphson's method with initial guess of 3.…

A: Detailed explanation and solution of the above problem uploaded in below pictures.

Q: A projectile is shot directly away from Earth's surface. Neglect the rotation of the Earth. What…

A:

Q: Determine the location y of the centroidal axis x-x of the beams cross-sectional area. Neglect the…

A: To find: The centroid of the beam. Given: The cross-section of the beam is shown below.

Q: 7. Show the V-M diagram using Area Method of the following beam:

A:

Q: A 3 in radius disk spins at the constant ω1 - 5 radian/s and a constant rate ω2= 4 radians/s. If the…

A:

Q: e hanging corner 3.5 ft 3.5 ft -1.5-ft diameter hole

A: Given system:  And density = 100 lb/ft2

Q: RAH A 60° RAV wwww 500 N E 60° 3m 60⁰ 60⁰ D RBV = 112.89 N RBV = 156.82 N RBV = 206.73 N O RBV =…

A: Given: find the vertical reaction of the roller at B.

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.