In the case of plane stress, where the in-plane principal strains are given by ε1 and ε2, show that the third principal strain can be obtained from
where v is Poisson’s ratio for the material.
To show that: The third principal strain can be obtained from
Answer to Problem 10.1RP
The third principal strain can be obtained from
Explanation of Solution
Given information:
The third principal strain
Explanation:
For the case of plane stress
Apply the normal strain in x direction as shown below.
Here, E is the modulus of elasticity,
Substitute 0 for
Multiply both sides of the Equation by
Apply the normal strain in y direction as shown below.
Substitute 0 for
Apply the normal strain in z direction as shown below.
Substitute 0 for
Adding Equation (1) and (2).
Substitute
Substitute
Therefore, the third principal strain can be obtained from
Want to see more full solutions like this?
Chapter 10 Solutions
Mechanics of Materials (10th Edition)
Additional Engineering Textbook Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Degarmo's Materials And Processes In Manufacturing
DESIGN OF MACHINERY
Foundations of Materials Science and Engineering
Engineering Mechanics: Statics
Vector Mechanics For Engineers
- A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?arrow_forward- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?arrow_forwardThe state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.arrow_forward
- The state of strain on an element has components Px = -300(10-6), Py = 100(10-6), gxy = 150(10-6). Determine the equivalent state of strain, which represents (a) the principal strains, and (b) the maximum in-plane shear strainand the associated average normal strain. Specify the orientation of the corresponding elements for these states of strain with respect to the original elementarrow_forwardA tri-axial state of stress, σx , σy, and σz ,exists in a steel machine part. For steel, E = 200GPa and ν = 0.3. Determine the normal strain in the x-direction if σx = 100MPa, σy = 35MPa, σz = 70MPa. Determine the dilatation. Determine the modulus of rigidity.arrow_forward(b) A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has the following components: ex = 150µ, ey = 200μ , γχν = -700μ. By using the strain transformation equations, determine:- The equivalent in-plane strains on an element oriented at an angle 0 = 60° counterclockwise from the original position. (ii) Sketch the deformed element within the x' – y' plane due to these strains. (iii) The stresses on the oriented planes in (i) where the value of elasticity, E = 200 GPa and Poisson's ratio, v = 0.32. (iv) Give your comments on those stresses in (iii) in terms of elastic limit/failure if the material's yield strength in tension/compression is 250 MPa and in shear is 90 MPa.arrow_forward
- 5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.arrow_forwardThe state of strain in a plane element is ex =-200 x 10-6, Ey = 0, and yxy = 75 × 10-6 , as shown below. Determine the equivalent state of strain which represents (a) the principal strains (b) the maximum in-plane shear strain and the associated average normal strain. Specify the orientation of the corresponding elements for these states of strain with respect to the original element. y Yxy 2 dy Yxy FExdx dxarrow_forwardA 60 ̊ strain rosette measures the following strain at a point on the aluminum skin of an airplane. ε0 = 160 ×10-6 m/m, ε60 = -220 ×10-6 m/m and ε120 = 360 ×10-6 m/m. Using E= 10 ×106 psi and v = 0.3, Determine the principle stresses and the maximum in-plane shear stress.arrow_forward
- For the given plane strain state, use Mohr's circle to determine the strain state associated with the x' and y' axes rotated to θ indicated in the table: \epsilon_x \epsilon_y \gamma_{xy} θ -500\mu 250\mu 120\mu -15°arrow_forwardA plane strain field at certain point in a body is described by the following strains; E. = +200 μ in/in, E60 +300 u in/in and E120 -100 μ in/in. Analyse the state of strains to determine, principal stresses, maximum shear stresses and their orientations. Take E = 29 x 106 psi, v = 0.3.arrow_forwardA rectangular aluminum plate of uniform thickness has a strain gauge at the center. It is placed in a test rig which can apply a biaxial force system along the edges of the plate as shown below. If the measured strains are +0.0005 and +0.001 in the x and y directions respectively, a) Determine the corresponding stresses set up in the plate and the strain through the thickness, εz. Take E=72 GPa and ν=0.32. b) Construct the Mohr’s circle for the loaded plate. c) State the values of the principal stresses. d) Determine the maximum shearing stresses and the directions of the planes on which they occur.arrow_forward
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning