What are some of the advantages to the consumer of standardization and of interchangeable parts?
Advantages to the consumer of standardization and of interchangeable parts.
Answer to Problem 1RQ
Advantages to the consumer of standardization and of interchangeable parts is listed below.
Explanation of Solution
Standardization is the technique in which number of different parts is reduced within the product. It aims on producing consistent products that meets the standard norms so that consumer is aware of the product.
Interchangeability means integration of any parts if a product fails. Interchangeable parts are the identical parts that are produced for replacement of any failed product part.
Some of the advantages to the consumer of standardization and of interchangeable parts is listed below.
- Mass- production of products in large volume
- High speed automated equipment
- Low cost per unit
- Integration of identical products if a product fails
Conclusion:
Thus, advantages to the consumer of standardization and of interchangeable parts is listed below.
Want to see more full solutions like this?
Chapter 10 Solutions
Degarmo's Materials And Processes In Manufacturing
Additional Engineering Textbook Solutions
Applied Statics and Strength of Materials (6th Edition)
Engineering Mechanics: Statics
Heating Ventilating and Air Conditioning: Analysis and Design
Fundamentals Of Thermodynamics
Mechanics of Materials (10th Edition)
Applied Fluid Mechanics (7th Edition)
- In the context of our teaching, which one of the below statements is mostly correct about in detailed design of a component? In the reporting, I do not need to include the reasoning for my design decision for a good quality report. I cannot use appendix, so I am struck with the word limit for reporting. For a good clarity, I should not explicitly report what are the key dimensions and their tolerances in the drawing and in the body of text. The word count limit for detailed design report is 160O.arrow_forwardWhich one of the below statements is mostly NOT correct about in creation of detailed design of component? The selection of material is based on what is required to performance the function. The tolerance is determined by the function, not the preference of designer or manufacture. In the selection of manufacturing processes, the number of components to be manufactured needs to be considered, as the capital investment needs to be considered. I do not need to show or prove the component is working: such how much electricity is generated in power panel, how much braking force is generated in by the brake disc, or how much the force the component in suspension is subjected?arrow_forwardWhat are the visual inspection standard's limitations of acceptance?arrow_forward
- 4. Describe the dimensions: design quality and conformance quality.arrow_forwardhand written plz 6. Design for , that is, the load can be taken by other members or the effect of fatigue failure otherwise mitigated, until the failed component can be detected and repaired or replaced. This approach is common in aircraft structural design. 7. create variations in dimensions, which can affect wear and fatigue properties. 8. is often used as the starting point to identify the most important problems and the most likely causes. 9. is a type of failure mode identification test, which use one/two samples to establish multiple design inherent failure modes, and establish operating and destruct limits of a product. 10. concerns the improvement in reliability, during use, that comes from field data feedback resulting in modifications.arrow_forwardParts of the Universal Testing Machine.arrow_forward
- Which organization sets the standards for dimensioning and tolerancing practices?arrow_forwardHW001 What things we measure with the help of vernier?arrow_forward28 - Which one is not one of the usage areas of control gauges? A) Control gauges are used to control the geometric profile of workpieces. B) Control gauges are used to control the dimensional measurements of mass-produced parts. C) Control gauges are used to control the fine adjustments of other measuring instruments. D) Control gauges are used to measure axial misalignment. E) Control gauges are used to control the surface quality of workpieces.arrow_forward
- a) Name two groups of standards in addition to national, industry-wide standards and where they are valid. b) Which three options exist for defining dimensional tolerances in a technical drawing?arrow_forwardProvide a description of the structure of an application that is capable of meeting the requirements for automobile safety inspections.arrow_forwardFive engineers measure the thickness of a slab using a meter stick and a vernier caliper. One engineer got a thickness of 4.3 cm ± 0.1 cm using a meter stick, the other four engineers measured a thickness of (a) 4.32 cm ± 0.01 cm, (b) 4.31 cm ± 0.01 cm, (c) 4.24 cm ± 0.01 cm, and (d) 4.43 cm ± 0.01 cm respectively using the caliper. Which of these four measurements made by the four engineers agree with the measurement obtained by the engineer that used a meter stick? Only a (b) and (c) (c) and (d) (a), (b), and (c) none of thesearrow_forward
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning