Are numbering systems other than the one described in this text used to develop wiring diagrams from schematic diagrams?
Whether the number system other than the one that are described in the text are used to determine the wiring diagrams from the schematic diagram.
Explanation of Solution
Consider the figure 24-1 in the text book for the schematic of the numbered components, consider Figure 24-2 in the text book for the schematic that has the component of the wiring diagram and is labelled by the numbers and correspond to the number component.
Then, consider the Figure 24-3 for the wiring diagram for the connected wires.
Thus, this method to number a schematic is used by a professional in electric troubleshooting.
There are many other way to number the systems other than one that is described in the textbook but every method has the same principle.
This shows that the number system is used to determine the wiring diagrams from the schematic diagrams.
Want to see more full solutions like this?
Chapter 24 Solutions
Industrial Motor Control
- Following the procedure discussed in Chapter 7, place wire numbers on the schematic in Figure 8–7. Place corresponding wire numbers on the components shown in Figure 8–8.arrow_forward3 Write the names of the following connection types and the elements used.arrow_forwardWhat is a software switch?arrow_forward
- Please explain the schematic diagram.arrow_forwardAnswer the following questions. Please I really need help. Even if you write something easy, I beg you. pleaseeeeeExplain in your own words how the Battery testing (performance test) is applied to the patient turning apparatus shown in the figure, and guess how the expected result will be. In addition, there are heating pads working with the logic of electric blankets in this apparatus but consider that it works with a battery, not a plug. Please answer by taking these into account when answering.arrow_forwardWith schematic diagramarrow_forward
- Drawing an arc using the polyline command will spawn the same possibilities as employing the arc command alone * O Not relevant at all O True O Falsearrow_forwardWhich type of control system is used in the given block diagram? Write the definition.arrow_forwardSelect the proper choice(s) for each of the following statements: 1) To control single-acting cylinder we just need: double-acting cylinder we should use A2/2-way, 5/2-way, (C) 3/3-way, 3/4-way, 2) In DCV. (B) 3/2-way, 4/2-way, (D) 4/3-way, 3/2-way. mid poistion of DCV, we can move cylinder piston rod freely without resistance by hand. (A) working ports are exhausted, (C) working ports are pressurized, 3) In pneumatics we use A Compressor (B) Pump, DCV, while to control the 4) Quick exhaust valve is used to (A) increase the cylinder return speed. (C) meter-out the cylinder speed (B) all ports are closed. no one of these options. to obtain high pressure air. (C) Turbine, (D) pressure relief valve. (B) meter-in the cylinder speed, (D) increase the cylinder extending speed. 6) Meter-in of cylinder movement is used to control the Afluid that enters the hydraulic cylinder, (B) fluid that exits the hydraulic cylinder, (C) fluid that enters the DCV (D) fluid that exits the DCV. 5) One of the…arrow_forward
- :The number of essential row exchanges is None 2 0 1 0arrow_forwardDraw a net circuit by hand using a ruler in the grid provided sheet below. connect it in the right way.arrow_forwardA pick and Place machine is being used to transfer a box. The arm is extended (out) by energizing a solenoid valve; when the valve is de-energizes, the arm retracts (in). In the same way, a second valve closes the grip (when energized) or opens the grip (when de-energized). Here's a diagram of this "machine": Grip Air Cylinder Grip open Grip Closed Box Arm Air Cylinder Arm In Arm Out The system is really slow... it actually takes 3-4 seconds for the arm to fully extend. An engineer created the below diagram. Start Pressed Time (seconds) Box Falls - 1 -2 -3 - 4 - 5 -6 –7 -8 – 9 – 10 Extend Arm Close Grip Question (finally!). Which statement is completely true regarding this design? It uses the Master Clock scheme. Given this diagram, the arm will probably start to retract before the grip fully closes. O If the arm takes 4 seconds to retract (return), the box will be dropped "mid-flight" It uses the Domino Scheme. Things can't happen in the wrong sequence. It uses the Master Clock…arrow_forward
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning