1. Determine the value of M1 if the system shown is equivalent to a single force acting at point C. 2. The system shown is equivalent to a force-couple system consisting of R and M2 = 3000 kip-in clockwise. If M1 in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD.

1. Determine the value of M1 if the system shown is equivalent to a single force acting at point C. 2. The system shown is equivalent to a force-couple system consisting of R and M2 = 3000 kip-in clockwise. If M1 in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.) The Force F produces a moment of F+B N•m clockwise at point A, and equal magnitude of moments (in N-m) directed counter – clockwise at point B and clockwise at the origin 0. The Force F acts at point C. Determine the following: a.) The Force F. b.) The coordinate y. Substitute: B=465, C=9, F=2060 y A(0, C). C(6,y) 4 O(0,0) B(6,0) F 3:
1) In the figure shown, a force F passing through C cause a.. 1) In the figure shown, a force F passing through C cause a clockwise moment of 120 ft-lb about A and a clockwise moment of 70 ft-lb about B. Determine the force and it's x-intercept. Action line of P F, B F.
Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. 270 N 720 mm 720 mm 160 N 720 mm 285 N Answers: Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. R= N N-m Single resultant force. d= i mm
Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. Answers: R= i M = IN 230 N i 320 N Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. d = i Single resultant force. 230 N 770 mm 770 mm 770 mm N N-m mm
Determine the moment of the vertical reaction at point.A (A,) rotating about the location (XR) of the equivalent resultant force of the forces acting on the beam shown in Figure 3.1h, i.e. Ay x XR. Given /= 2.2, P1 = 40, P2 = 80, w1 = 20 and w2 = 40. (Note: Negative "-" for clockwise moment.) [Hint: Find the equivalent resultant force and its location (xR) with respect to point A. Apply correct equation of equilibrium to solve Ay.] P, kN P2 kN W, kN/m W2 kN/m B I m 21 m 21 m Figure 3.1h
The 23-N force Pis applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. Moments are positive if counterclockwise, negative if clockwise. P = 23 N 2.0 m 49 B 2.0 m A Answers: MB = i N-m MA = N-m
Please solve using 3 kip instead of 2 kip for the downward force 2 kip at P a 60° 1 kip The end of a cantilever I beam supports forces from three cables. a) If P = 0, determine the resultant force applied by the two cables to the I beam and report your result using polar vector representation. b) Repeat Part (a) if P = 1.5 kip and ? = 30?. c) With ? = 30?, what value of P will produce a resultant force that is horizontal? d) If the resultant force is to be horizontal and Pis to be as small as possible, determine the value ? should have and the corresponding value of P.
5. The resultant of the three forces shown is the force R = 200 N acting along z-axis. Determine P1, P2, and P3. B A P₂ Z C 150 mm 200 mm P₁ 120 mm 150 mm P3 320 mm
At point O, replace the force system with a resultant force and couple moment. FR= Answer in N θR= Answer in ˚ Mo= Answer in N.m
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F D E b G B Ө 0 P b b C Zoom image Compute the force induced in member DB. C P
The control lever is subjected to a clockwise couple of 115 N-m exerted by its shaft at A and is designed to operate with a 330-N pull as shown. If the resultant of the couple and the force passes through A, determine the proper dimension x of the lever. Assume F = 330 N, a = 135 mm, 0 = 20° F A 3 a Answer: x = i mm
A 599-N force is applied at A as shown. y = 469 mm. Determine (a) the moment of the 599-N force about D in N-m. Write numerical value and 2 decimal places. + for counterclockwise y mm 25° P 100 mm D -200 mm 125 mm C B