10)A screw clamp similar to the one shown in the figure has a handle with diameter in madeof cold-drawn AISI 1006 steel. The overall length is 3 in. The screw is in-14 UNC and is5 in long. overall. Distance A is 2 in The clamp will accommodate parts up to 4 in tagh.(a) What screw torque will cause the handle to bend permanenly?See sample problem 10.1, sections 10.4, 10.7Given;hordle dia :16inL: 3in.Disa: Zin10/29Find: Scrcw torque ,!Assumphon : The screw torque isfar cold decunAISI 1006 steel.aL: 3-82.406 in%3D432T: 2.406FH:(L-3) -굵)F. 2.188FF- (2406F: 2.188FSy: 41 Kpsi.32 (2-188) FTI (O.1875)3Sy = 32MF-12:13 1bfT. 2.406 CI2:13) =29.216f. inThe lorque of the screwwhich will couse thescoch to bend pemorently is 29.21of. in.is 29.210f.10.

Given Screw clamp To find Torque it can handle

10) A screw clamp similar to the one shown in the figure has a handle with diameter in made of cold-drawn AISI 1006 steel. The overall length is 3 in. The screw is in-14 UNC and is 5 in long. overall. Distance A is 2 in The clamp will accommodate parts up to 4 in tugh. (a) What screw torque will cause the handle to bend permanently? See sample problem 10.1, sections 10.4, 10.7

10) A screw clamp similar to the one shown in the figure has a handle with diameter in made of cold-drawn AISI 1006 steel. The overall length is 3 in. The screw is in-14 UNC and is 5 in long. overall. Distance A is 2 in The clamp will accommodate parts up to 4 in tugh. (a) What screw torque will cause the handle to bend permanently? See sample problem 10.1, sections 10.4, 10.7

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A screw clamp shown in the figure has a horizontal handle with diameter 3/8-in made of cold-drawn AISI 1006 steel. The overall length of the handle is 4.25 in. The screw is single-threaded, 3/4 in-10 UNC, and is 8 in long, overall. a. What screw torque will cause the horizontal handle to bend permanently? b. What clamping force will the answer to part a) cause if the collar friction is neglected and if the thread friction is 0.15? Hint: 1) Assume a force Fis applied at the end of the handle. Think about how this force affects the screw vs. how it affects the handle. 2) Consider in which direction the screw is "raised". - 4.25 in
Design a hard steel (screw and nut) lubricated power screw for raising and lowering a load of 25 kN using a square – thread with major diameter of 40 mm, pitch of 6 mm with triple threads and a plain bronze thrust collar of 60 mm (fc=0.08) (Assume maximum friction). (a) Find the torque for raising and lowering the load. Is the design self-locking? If not, please change the design accordingly (b) Find the largest axial and shear body stresses. Also find the bending stresses (c) With a safety factor of 2, a designer has chosen the DE approach to design the power screw with Sy = 260 MPa. Is this a suitable option?
The figure below shows a boat propeller mounted on a drive shaft with a 7 mm diameter (d) cylindrical drive pin inserted through the hub and the shaft. The drive shaft diameter, D, inside the hub is 69 mm. The pin is made from AISI 1020 cold rolled steel, which has a yield stress of 427 MPa and an ultimate stress of 621 MPa. If the drive pin is subjected to an overload (e.g. strikes a log), calculate the torque (Nm) required to shear the pin. Note: Assume that the max shear stress of the pin material is approximately equal 82% of the ultimate tensile stress. Do not include units in your answer. Pin F Hub Drive pin Shaft Drive shaft F Shear planes Hub Answer:
For a square thread power screw, given that:F= 6.4 kNPitch = 5 mmMajor diameter = 32 mmTotal raising torque = 28 N.mThen then max. torsional shear stress equals:
A screw clamp similar to the one shown in the figure has a handle with diameter in made of cold-drawn AISI 1006 steel. The overall length is 3 in. The screw is in-14 UNC and is 5 in long, overall. Distance A is 2 in. The clamp will accommodate parts up to 4 in high. (a) What screw torque will cause the handle to bend permanently? (b) What clamping force will the answer to part (a) cause if the collar friction is neglected and if the thread friction is 0.075? ट Problem 8-7 B !!!!!!!
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.
Please answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the bolt circle is 2=150mm. If the allowable shear stress in the bolts is 90 Mpa, what is the maximum permissible torque? Disregard friction between between flanges. The To
34 in 3. The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))
A screw clamp shown in the figure has a handle with diameter 5 mm made of cold-drawn AISI 1006 steel (table E18 - page 1195). The overall length of the hand is 75 mm. The screw is M 12 coarse (table 8-1) and is 145 mm long, overall. Distance A is 50 mm. The clamp will accommodate parts up to 105 mm high.a) What is the value of screw torque that causes the handle to bend permanently?b) If the collar friction is neglected and if the thread friction is 0.075, what is the screw force value that causes the handle to bend permanently?c) What is the value of clamping force, which will cause the screw to buckle?d) Are there any other stresses or possible failures to be checked?e) If yes, calculate them.
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter dp / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gp = 28 Gpa. R Rs Rb
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter d, / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, G, = 28 Gpa. %3D Rs Rp
Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm diameter solod shaft supported by the bearings is to be made of machined AISI 1045 CD steel. The helical gear is subjected to the axial force F-498 y a radial load F- 750 N and a tangential load of F-1.995 N. Assume the component is g at room temperature of 70F and the material has s0s reliability factor. Hint: Be careful when you calculate the bending moment at the fillet, as all the three forces on the helical gear cause bending moment at the fillet. Calculate resultant bedina moment from all the three forces. Bending moment is completely reversed loading.) 25-mm solid round shaft Fillet Bending K, = 2.0 Torsional k, = 1.5 Axial K,18 F. F, F Pump Helical spur gear -50 mm -250-mm dia FIGURE 1. Identify the critical locations) of stress and show it clearly in a diagram. 2 Identity cleary, all the components of stresses (at the critical point) that will be calcurated (by drawing and clearty…