3 in The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))

3 in The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Information about the clamp assembly in the figure is given below. Thread diameter 12 mm, root diameter 10.16 mm, pitch 1.5 mm, screw profile angle 2α=60, friction surface of table A diameter 10 mm, friction between plate A-screw end surface coefficient 0.15 and screw-nut friction coefficient 0.15 is given. If a hand force of 200N is applied to the vise arm, if applied, a) How much force is applied to the clamped part. b) Calculate the efficiency of the vise.
Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn waste chipper/shredder. As the engine operates at 1200 rpm, the shredding teeth should rotate at 240 rpm. The drive sprocket has 18 teeth. Determine an appropriate pitch for the chain, the number of teeth on the driven sprocket, the pitch diameters of both sprockets, and the chain speed. Also indicate the number of links in a suitable chain and specify the required center distance.
A A10¹ 4 bartleby.com/questions-an Q SEARCH ASK 愚CHAT VX MATH SOLV A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to overcome the collar friction? Group of answer choices 630000 N mm 315000 N mm 819000 N mm 409500 N mm Expert Solution Step 1 Given: W = 70 KN d = 33.375 mm p=6 mm 11-tand-013 9:26 AM Q मं
Question 3 A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of 34 mm and a pitch of 6 mm is used. The coefficient of friction at the thread and collar are 0.15 and 0.1 respectively. If the collar frictional diameter is 100 mm and the screw turns at a speed of 1 rev/s. (Given dm = 31mm, 1 = 6mm, dc = 100mm). Find: (a) the power input to the screw. (b) the combined efficiency of the screw and collar.
A. PROBLEM ON TOPIC "KEYS AND COUPLINGS": A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the 1.75 inch shaft... is also AISI C1045 as rolled and the key is cold drawn AISI C1020. N= 2.5. Determine the following: 1. Size of bolt (dia.) if there are 6 bolts made of AISI C1045 as rolled at a bolt circle of 5 inches. Note: Select standard bolt diameter from AT14 of DOME by Faires (see Lecture on fasteners for this Table) Calculated Dia: Standard Size to use: 2. Required b and t if a flat or rectangular key is used: Answer: 3. Required length of key, if a flat or rectangular key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use: 4. Required bif a square key is used: Answer: 5. Required length of key, if a square key is used: Note: Calculate for two type of stresses on kev, then select your answer. Length Based on shear length Based on compression:…
The following data apply to the machinist clamp shown in the figure: Outside diameter of screw=1/2 in.; Root diameter=0.4350 in.; Pitch (single thread)=0.05 in.; Collar friction radius=0.20 in.; Collar friction coefficient=0.15; and screw friction coefficient=0.15. Assume that the machinist can comfortably exert a maximum force of 30 lbs. on the handle.Determine: (a) the clamping force developed between the jaws of the clamp; (b) the efficiency of the clamp; (c) the torque in the screw body at section A-A
7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative image) has 48 teeth on front sprocket (Crank side), the diameter of front sprocket being 10.5 inches. The rear wheel has a cassette with a cluster of 6 sprockets, with number of teeth on Sprocket #1 (lowest gear) to Sprocket # 6 (highest gear) being 30, 26, 23, 20, 16 and 12, respectively. (Ignore wind resistance and friction between machine elements) (a) If the rider is pedaling at a constant 105 rpm with an effective force of 28 lb acting on periphery of front Sprocket (at 5.25 inch radius length, the force location indicated by red arrow), and is engaged in Sprocket #5, what would be the torque acting on Sprocket # 5, and the RPM at which the rear wheel is spinning? (b) For the condition as described in (a), If the diameter of wheels is 26 inches, what is the speed of the bicycle? &
1-Show how the roughness is indicated for a Surface to be coated, obtained by any production method with N6 showing max. and min roughness. 3- gearing is suitable for two shafts at 90°. : Draw five turns of a compression spring of wire diameter 6mm, pitch 12 num and outside diameter of 38mm.
2- Give the true representation of screw thread from the following, and mark the reasons for the false. (4) (1) (5) ■ (3) ك
4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of 17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
Q1- Find the power required to drive a 1.5-in power screw having double square threads with a pitch of 1/4 in. The nut is to move at a velocity of 2 in/s and move a load of F = 2.2 kips. The frictional coefficients are 0.10 for the threads and 0.15 for the collar. The frictional diameter of the collar is 2.25 in. ca1-
For a square thread power screw, given that:F= 6.4 kNPitch = 5 mmMajor diameter = 32 mmTotal raising torque = 28 N.mThen then max. torsional shear stress equals: