1)For the mechanical system shown, m = 1 kg and k = 600 N/m. Derive the expression for the peakamplitude ratio M, and resonant frequency w, for any arbitrary value of c. Generate a plot for w, vs. c,and another plot for M, vs. c, and explain how changing the damping in the system affects theseparameters. Make your plots for 0 ≤ c≤ 30 N.s/m.m12xwwwK

Step 1: Step 2: Step 3: Step 4:

Answered: 1)For the mechanical system shown, m =…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single degree of freedom mass-spring-damper system is subject to vibration under the influence of a harmonic force. On my site, it is given as m=2 kg, k=800 N/m, c=64 Ns/m. The amplitude of the harmonic force is F0=256 N and its frequency is w= 20 rad/s. Answer the questions in options a, b, and c according to the given information. 1) Calculate the damping ratio of the system (ξ) a.1 b.0.7 c.0.9 d.0.8 2)Calculate the magnification factor (M) of the system. a.0.86 b.1.25 c.0.312 D.0.625 3-) Calculate the maximum vibration amplitude (X) (meters). a.0.2 b.0.1 c.0.4 D.0.3
For the mechanical system shown, a- Find the equivalent mass, equivalent spring stiffness and equivalent damping coefficient when x (the displacement of the 2 kg block) is used as the generalized coordinate. b- Derive the equation of motion of the system in terms of equivalent system parameters (equivalent mass, equivalent spring stiffness and equivalent damping coefficient). 3000 N/m 2 kg 200 N.s/m /=0.04 kg-m² r = 10 cm 1000 N/m 1 kg I' 400 N.s/m ial
Given an oscillator of mass 2.0kg and spring constant of 180N/m, what is the period without damping? Use numerical methods to model this oscillator with an additional friction force equal to where c is a positive damping constant. Using c=5.0, what is the new period of oscillation. What about for c=10? Assume initial position is 0.2m and initial velocity is zero. Please find the period using the position versus time plot and use the first full cycle of the motion.
Q1/ An instrument vibrate with a frequency of 1 Hz when there is no damping. When the damping is provided, the frequency of damped vibrations was observed to be 0.9 Hz. Find (1) the damping factor, and (2) logarithmic decrement.
A weight of 10lb is suspended by a spring having a modulus of 15 lb-s/in. When displaced and permitted to oscillate freely, it is found that the amplitude diminished from 1.5 in to 1.316 in in exactly 10 cycles. a.) determine the system mathematical model. Just show the illustration of the mathematical model.
Consider a second order system given by 7 d²x(t)/dt² + 3 dx(t)/dt + 24 x(t) = t. What is the damping ratio? Do not include units. Write your answer in scientific notation using 3 significant figures. (e.g. 1.23e0)
The 8kg body is moved to the right of the equilibrium position and released from rest at time t = 0. The viscous damping coefficient is 23NS/m and the spring stiffness, K is 38N/m. Determine the damping factor (ratio) of the system. Note: Give your answer to 3 decimal places. Other Parameters: Logarithmic Decrement (8): Answer: 2ng 2T C 8 = In = In1 = 5 wnTd = 5wn X2 Xn+1 1-5 wa 2m k Damping Ratio (5): 5= 2vkm 2mn V(21)2+8 Frequency of damped vibration (wa): wa = 1-Wn Undamped Forced Vibration: Frequency Ratio (): r- Xp-x sin w t Next page Hous page Type here to search
An oscillator system without damping has a natural frequency of omega 0 = pi rad/s. Several types of attenuation are given to the system to provide a damping factor (y) of 0.1, 0.5 and 1 s^-1. (a) For each damping factor value, determine the omega value of the oscillator!. (b) determine the displacement at time t = 2 seconds for the damping factor y = 0.5 , if the displacement at t = O is 30 mm and v = 1.5 m/s
1) For the mass-damper system at right, the model in terms of velocity is mv + cv = f. The time constant of this first order system is t = m/c. For this system, a larger value of the damping constant c causes the time constant to decrease - which is counterintuitive. It seems that a small amount of damping should correspond to a system with a fast response. How can you reconcile this? m CA
For the system shown in Figure 2, u (t) and y (t) denote the absolute displacements of Building A and Building B, respectively. The two buildings are connected using a linear viscous damper with damping coefficient c. Due to construction activity, the floor mass of Building B was estimated that vibrates with harmonic displacement that is described by the following function: y(t) = y,cos (wt). k/2 Building A H k/2 M(t) C 73(1) Building B Equivalent (Building A) 00000000 Figure 2: Single-degree-of-freedom system in Problem 2. 111 uft) Please compute the following related to Building A: (a) Derive the equation of motion of the mass m. (b) Find the expression of the amplitude of the steady-state displacement of the mass m. (1) (Building B)
4. A convenient way to measure damping in a single-degree-of-freedom system is called logarith- mic decrement of free response. Consider the free response given by (4). Let's denote t₁ and t2 denote the times corresponding to two consecutive displacements ₁ and 2 measured one cycle apart, i.e., where t₂ = t₁ + T 2π Wd According to (4), show that the logarithmic decrement dis T = x1 8 = log = x2 where log has base e. Combine (5), (7), and (8) to obtain = (WnT 8 4π² +8² Will this method work for other initial conditions? why?
A mass of 5 kg is suspended on a spring and set on oscillations. It is observed that theamplitude reduces to 5% of its initial value after 2 oscillations. It takes 0.5 seconds to do thetwo oscillations. Calculate the following.(i) The damping ratio(ii) The natural frequency(iii) The actual frequency(iv) The spring stiffness(v) The critical damping coefficient(vi) The actual damping coefficient

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS